FT232RL R FTDI, Future Technology Devices International Ltd, FT232RL R Datasheet - Page 11

• Manufacturer Part Number: FT232RL R
• Description: IC USB TO SERIAL UART 28-SSOP
• Manufacturer: FTDI, Future Technology Devices International Ltd
• Series: USBmadeEZ-UARTr

Specifications of FT232RL R

• Features: USB to UART
• Number Of Channels: 1, UART
• Fifo's: 256 Byte
• Protocol: RS-232, RS-422, RS-485
• Voltage - Supply: 3.3 V ~ 5.25 V
• With Auto Flow Control: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP
• For Use With: 768-1023 - MOD USB RS232 DEV/EVAL FT232RL768-1022 - MODULE USB - SERIAL MODULE MINI768-1021 - MODULE MINI DEVELOPMENT FT232RQ768-1019 - MODULE USB-SER UART FT232 24-DIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 768-1007-2; FT232RL R

Table 3.6 Power and Ground Group
Table 3.7 Miscellaneous Signal Group
Pin No.
Pin No.
13, 23,
25, 29
5, 12,
No.
Pin
30
31
32
10
2
3
6
7
8
9
16
19
24
18
26
27
28
Name
CBUS4
CBUS2
DCD#
DTR#
DSR#
RTS#
CTS#
RXD
TXD
RI#
3V3OUT
RESET#
Name
Name
AGND
OSCO
TEST
OSCI
VCC
NC
Output
Output
Output
Type
Input
Input
Input
Input
Input
Copyright © 2010 Future Technology Devices International Limited
I/O
I/O
Output
Output
Type
Type
Input
Input
Input
PWR
PWR
NC
Transmit Asynchronous Data Output.
Data Terminal Ready Control Output / Handshake Signal.
Request to Send Control Output / Handshake Signal.
Receiving Asynchronous Data Input.
Ring Indicator Control Input. When remote wake up is enabled in the internal EEPROM
taking RI# low (20ms active low pulse) can be used to resume the PC USB host
controller from suspend.
Data Set Ready Control Input / Handshake Signal.
Data Carrier Detect Control Input.
Clear To Send Control Input / Handshake Signal.
Configurable CBUS output only Pin. Function of this pin is configured in the device
internal EEPROM. Factory default configuration is SLEEP#. See CBUS Signal Options,
Table 3.9.
Configurable CBUS I/O Pin. Function of this pin is configured in the device internal
EEPROM. Factory default configuration is TXDEN. See CBUS Signal Options, Table 3.9.
+3.3V output from integrated LDO regulator. This pin should be decoupled to
ground using a 100nF capacitor. The purpose of this output is to provide the
internal +3.3V supply to the USB transceiver cell and the internal 1.5kΩ pull up
resistor on USBDP. Up to 50mA can be drawn from this pin to power external logic if
required. This pin can also be used to supply the VCCIO pin.
+3.3V to +5.25V supply to the device core. (See Note 1).
Device analogue ground supply for internal clock multiplier.
No internal connection. Do not connect.
Active low reset. Can be used by an external device to reset the FT232R. If not
required can be left unconnected, or pulled up to VCC.
Puts the device into IC test mode. Must be tied to GND for normal operation,
otherwise the device will appear to fail.
Input 12MHz Oscillator Cell. Optional – Can be left unconnected for normal
operation. (See Note 2).
Output from 12MHZ Oscillator Cell. Optional – Can be left unconnected for normal
operation if internal Oscillator is used. (See Note 2).
FT232R USB UART IC Datasheet Version 2.07
Description
Description
Description
Document No.: FT_000053
Clearance No.: FTDI# 38
11