TDA9321H Philips Semiconductors, TDA9321H Datasheet
TDA9321H
Specifications of TDA9321H
Available stocks
Related parts for TDA9321H
TDA9321H Summary of contents
Page 1
... DATA SHEET TDA9321H 2 I C-bus controlled TV input processor Preliminary specification Supersedes data of 1998 Dec 16 File under Integrated Circuits, IC02 INTEGRATED CIRCUITS 2000 Sep 25 ...
Page 2
... I C-bus control of various functions Low dissipation. 2000 Sep 25 GENERAL DESCRIPTION The TDA9321H (see Fig. input processor for ‘High-end’ television receivers. It contains the following functions: Multistandard IF amplifier with PLL demodulator QSS-IF amplifier and AM sound demodulator CVBS and Y/C switch with various inputs and outputs ...
Page 3
... Sep 25 PACKAGE DESCRIPTION plastic quad flat package; 64 leads (lead length 1.95 mm); body 14 20 2.8 mm PARAMETER and and Preliminary specification TDA9321H VERSION SOT319-2 MIN. TYP. MAX. UNIT 7.2 8.0 8.8 V 120 100 V 1 ...
Page 4
... SYS1 SYS2 YCF COMB FILTER DEC DIG DEC BG PH1LF HA/CLP SCO PULSE VERTICAL SUPPLY GENERATOR DIVIDER TDA9321H VERTICAL VCO AND SYNC HORIZONTAL PLL SEPARATOR IDENT SYNC VIDEO SYNC IN-LOCK IDENTIFICATION SEPARATOR DETECTOR AUTOMATIC CLOCHE FILTER CHROMINANCE FILTER TUNING CONTROL hue PAL/NTSC ...
Page 5
... DEC SEC 2 C-bus) XTALA XTALB XTALC XTALD PH1LF SCO HA/CLP VA TAGC SIF1 SIF2 5 Preliminary specification TDA9321H DESCRIPTION 33 digital supply decoupling 34 CVBS output for teletext 35 band gap decoupling 36 red input 1 37 green input 1 38 blue input 1 39 RGB insertion input 1 40 ...
Page 6
... DEC VIF 4 QSS/AM 5 VIFPLL 6 VIFVCO1 7 VIFVCO2 8 GND1 9 VIFO GDI 12 GDO 13 CVBS int 14 AV1 15 CVBS1 16 AV2 17 CVBS2 18 SW0 19 2000 Sep 25 TDA9321H Fig.2 Pin configuration. 6 Preliminary specification TDA9321H SDA 46 SCL GND3 BI2 43 42 GI2 RI2 41 40 RGB2 39 RGB1 38 BI1 37 GI1 36 RI1 DEC CVBSTXT ...
Page 7
... The video ident circuit can also be used to identify the selected CBVS or Y/C signal. The switching between the two modes can be realized with bit VIM. The TDA9321H contains a group delay correction circuit 2 C-bus. The which can be switched between the BG and a flat group delay response characteristic ...
Page 8
... The circuit can also decode the PALplus helper signal and can insert the various reference signals, set-ups and timing signals which are required for the PALplus decoder ICs. 2 C-bus so that the The baseband delay line (TDA4665 function) is integrated. 8 Preliminary specification TDA9321H 2 C-bus 2 C-bus transmission. 2 C-bus and which ...
Page 9
... Acrobat reader. white to force landscape pages to be ... VIM VIDEO ident IDENTIFICATION CVBS int CVBS1 CVBS2 Fig.3 Video switches and interfacing of video ident. TDA9321H CVBS/Y3 C3 CVBS/ luminance/sync processing to chrominance ...
Page 10
... The subaddresses are valid. The 2 C-bus (fast or slow). FE and FF subaddresses are reserved for test purposes. The auto-increment mode is available for subaddresses. 10 Preliminary specification TDA9321H 2 C-bus. To obtain short switching times ...
Page 11
... VIM 0 0 BSY ECMB DEC3 DEC2 PIP1 PIP0 0 TXT2 0 0 YUV ECL MOD AFW IFS CONDITION 0 crystal not present 1 crystal present; note 1 TDA9321H BPS YD1 YD0 POC VID EMG NCIN 0 0 DEC1 DEC0 TXT1 TXT0 IE2 IE1 OS1 OS0 STM VSW ...
Page 12
... The total Y-delay is the addition of: YD3 + YD2 + YD1 + YD0. Table 14 Forced field frequency FORF FORS Note 1. When switched to this mode the divider will directly switch to forced 60 Hz only. 12 Preliminary specification TDA9321H CENTRE FREQUENCY DELAY LINE MODE active bypassed GAI0 GAIN SETTING 0 ...
Page 13
... Table 21 Enable ‘Macrovision/subtitle’ gating EMG 0 1 Table 22 Vertical divider mode NCIN Preliminary specification TDA9321H CONDITIONS unblanked sync; note 1 blanked sync CONDITIONS clamp pulse available on pin HA/CLP horizontal pulse available on pin HA/CLP MODE disable gating enable gating VERTICAL DIVIDER MODE ...
Page 14
... AUTO COMB3; note AUTO COMB4; note 4 Table 25 Enable YUV input (on RGB1 input) YUV 0 1 int Table 26 External RGB clamp mode ECL Preliminary specification TDA9321H SIGNAL TO COMB CVBS int CVBS1 CVBS2 CVBS3 CVBS4 CVBS3 CVBS4 CVBS int CVBS1 CVBS2 CVBS3 ...
Page 15
... STATE 0 normal operation 1 VIF signal switched off MODE 0 normal IF frequency 1 frequency shift for L’ standard DATA BYTE (1) ( SNR FSI CD1 CD0 SXD SXC CMB YC S2A S2B ID1 ID0 IFI PL TDA9321H IVW SXB SXA S1A S1B AFA AFB ...
Page 16
... PAL NTSC PAL NTSC PAL NTSC PAL SECAM illegal forced mode; note 1 16 Preliminary specification TDA9321H ) lock indication 1 INDICATION not locked locked STANDARD VIDEO SIGNAL no standard video signal standard video signal in ‘narrow window’ or standard TV norm (525 or 625 lines) CONDITIONS ...
Page 17
... PLL not locked 1 PLL locked Table 53 AFC output AFA AFB 0 0 outside window; too low 0 1 outside window; too high window; below reference window; above reference Table 54 IC version indication ID3 ID2 ID1 Preliminary specification TDA9321H CONDITIONS ID0 IC TYPE 1 TDA9321HN1 1 TDA9321HN2 ...
Page 18
... Negative stress test: I trigger 2000 Sep 25 CONDITIONS and for 5 s notes 1 and 2 notes 1 and 3 PARAMETER 1.5 V pin P(max) 100 0 pin P(max) 18 Preliminary specification TDA9321H MIN. MAX. 9.0 25 +150 0 70 260 150 3000 +3000 300 +300 CONDITIONS VALUE in free air 50 UNIT ...
Page 19
... VIFPLL); note 4 notes 5 and 6 2 via I C-bus with bit L’FA note 8 negative modulation positive modulation negative modulation positive modulation note 9 19 Preliminary specification TDA9321H MIN. TYP. MAX. UNIT 7.2 8.0 8.8 V 120 140 mA 960 mW 35 200 V 35 ...
Page 20
... Hz; system B/G VIF input signal amplitude increase of 52 dB; positive and negative modulation VIF input signal amplitude decrease negative modulation positive modulation negative modulation positive modulation capacitor on pin C-bus amb 20 Preliminary specification TDA9321H MIN. TYP. MAX. UNIT 2.5 deg 6.0 V 1 ...
Page 21
... BUS for identification after the AGC has stabilized on a new transmitter SIF2) FM mode ( 3 dB) AM mode ( 3 dB) AM mode note 3 note 3 QSS/AM) 21 Preliminary specification TDA9321H MIN. TYP. MAX. UNIT 9 V 300 0 bits 55 ...
Page 22
... SC subharmonics (f = 2.75 MHz 3 kHz) SC subharmonics (f = 2.87 MHz 3 kHz) 54% modulation C SIGNALS note MHz; note 6 i notes 3 and 18 22 Preliminary specification TDA9321H MIN. TYP. MAX. UNIT 70 90 110 mV 7.5 9 MHz 2 mV 53/48 58/55 dB 52/47 55/53 ...
Page 23
... OL I output sink current o(sink) I output source current o(source) 2000 Sep 25 CONDITIONS MIN. 1.6 0.8 0.8 burst amplitude 0.2 L 4.0 4 Preliminary specification TDA9321H TYP. MAX. UNIT 2.0 2 mV/K 250 1.0 1 mV/K 250 1.0 1.2 V 250 3.6 ...
Page 24
... MHz SC during SECAM reception bit bit bits YD3 to YD0 = 1011; note 6 crystal A crystal with respect to 520/560 ns; 12 settings; see Table 13 note 6 GDI GDO); note 24 AND 24 Preliminary specification TDA9321H MIN. TYP. MAX. UNIT 2.0 2.2 2.4 V 5.3 5.5 5 100 MHz osc 4 ...
Page 25
... S noisy input signals when the ACL starts to operate for a 400 Hz deviation of the oscillator frequency; note 6 note 10%; note steps; see Fig.4 V 10%; note note 6 amb note 6 25 Preliminary specification TDA9321H TYP. MAX. UNIT 3.0 360 600 Hz 2 deg 1 Hz/K ...
Page 26
... BPS) 26 Preliminary specification MIN. TYP. 1.60 1.78 650 Y) output Y) output Y) output Y) output 0 0.1 63.94 64 TDA9321H MAX. UNIT 1.96 kHz %/K 0.3 dB/V 5 deg 7 kHz 60 Hz/K 93 kHz 3 ...
Page 27
... YD3 to YD0 = 1011; note 30 only lines 22 and 23 RI2 BI2 clamping; note 3 note 6 27 Preliminary specification TDA9321H MIN. TYP. MAX. UNIT 610 686 770 mV 380 400 420 mV ...
Page 28
... MHz; note data insertion MHz; note 6 i black-to-white black-to-white black level MHz i bit MACP = 1 or bit note re-inserted black bl 28 Preliminary specification TDA9321H MIN. TYP. MAX. UNIT 1.0 V 1.33 V 1. 0.4 V 0.9 V 3.5 V ...
Page 29
... EBU colour bar note 3 note 32 note 8.0 V 10%; note note 6 amb note 6 for the video input signal at which the time constant is switched 29 Preliminary specification TDA9321H MIN. TYP. MAX. UNIT 1.35 1.43 1.50 1.08 1.14 1.20 0.88 1.05 1.25 V 1.12 1 ...
Page 30
... bit MACP = 1; bits YD3 to YD0 = 1011; at nominal horizontal frequency note mode 60 Hz mode not locked o(source o(sink Preliminary specification TDA9321H MIN. TYP. MAX. UNIT 5 ns 4.0 5.0 5.5 V 0.2 0 4.6 4.7 4.8 s 0.3 0.45 ...
Page 31
... CONDITIONS note 35 bit ECL = 1 note 30 SCL SDA) PINS AND 5 OL(SDA) SW1); note 36 AND must be decoupled separately but they must be connected to a single power supply P2 31 Preliminary specification TDA9321H MIN. TYP. MAX. UNIT 37 0.5 1.0 V 0.5 mA 2.2 2.5 2 ...
Page 32
... PAL-N, PAL-B/G and NTSC-M) and are controlled by the colour decoder identification circuit. The setting of the outputs for the various standards is given in Table 56. 2000 Sep kHz; damping factor calculated with top sync pF. 0 int 2 C-bus. Two bits are reserved for this function. The AFC value values as indicated Preliminary specification TDA9321H ...
Page 33
... MHz 20.6 fF (4.43 MHz crystal 5.0 pF. 2 C-bus bits GAI1 and GAI0 and with a gain variation between 1 and +2 dB) which 33 Preliminary specification = 18 pF. The oscillator circuit is rather pF 14.7 fF (3.58 MHz crystal). mot = account for parasitic capacitances on-chip s TDA9321H ...
Page 34
... Pins 19 and 22 are for general purpose outputs that can be used to switch external circuits e.g. sound traps, etc. They are controlled via the I 2000 Sep 25 2 C-bus by bits OS0 (pin 19) and OS1 (pin 22). 34 Preliminary specification TDA9321H 2 C-bus. Therefore the circuit contains a 2 C-bus. ...
Page 35
... IDENT COIN NOISE yes yes no yes yes yes yes no yes yes yes no yes yes no yes yes yes no 35 Preliminary specification TDA9321H REMARKS 5 mm long 100 ppm/ C ACTIVE CRYSTAL CURRENT/MODE SCAN V-RETR GATING (1) 180 270 yes 30 30 yes 180 270 yes ...
Page 36
... Philips Semiconductors 2 I C-bus controlled TV input processor handbook, full pagewidth (deg) 2000 Sep DAC (HEX) Fig.4 Hue control curve. MBC212 16 % for negative modulation 100% = 10% rest carrier Fig.5 Video output signal. 36 Preliminary specification TDA9321H MLA739 40 100% 92% 30% ...
Page 37
... Philips Semiconductors 2 I C-bus controlled TV input processor handbook, full pagewidth 100 (%) handbook, halfpage 2000 Sep Fig.6 Test signal waveform. 500 t d(g) (ns) 400 300 200 100 Fig.7 Group delay characteristic. 37 Preliminary specification TDA9321H MBC211 time ( s) MGR476 (MHz) ...
Page 38
... MHz O at 3.58 or 4.4 MHz O at 2.66 or 3.3 MHz O Fig.8 Input signal conditions. PC 38.9 MHz ATTENUATOR CC 34.5 MHz Fig.9 Test set-up intermodulation. 38 Preliminary specification MBC213 YELLOW TEST SPECTRUM CIRCUIT ANALYZER gain setting adjusted for blue or yellow MBC210 TDA9321H ...
Page 39
... CVBSTXT CVBSPIP 2000 Sep 25 RGB1 RGB2 RI2 GI2 BI2 FEATURE BOX CVBSCF YCF CCF COMB FILTER Fig.10 Application diagram. 39 Preliminary specification TDA9321H RI1 GI1 BI1 BL1 RI2 GI2 BI2 BL2 YIN 28 40 UIN 27 41 VIN TDA9330H MGR477 BCL BLKIN ...
Page 40
... Sep scale (1) ( 0.50 0.25 20.1 14.1 24.2 1 0.35 0.14 19.9 13.9 23.6 REFERENCES JEDEC EIAJ MO-112 40 Preliminary specification 18.2 1.0 1.95 0.2 0.2 0.1 17.6 0.6 EUROPEAN PROJECTION TDA9321H SOT319 detail X (1) ( 1.2 1 0.8 0.8 0 ISSUE DATE 97-08-01 99-12-27 ...
Page 41
... Use a low voltage ( less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 41 Preliminary specification TDA9321H ...
Page 42
... Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. 2000 Sep 25 SOLDERING METHOD WAVE (2) not suitable suitable (3)(4) not recommended not suitable (5) not recommended 42 Preliminary specification TDA9321H (1) REFLOW suitable suitable suitable suitable suitable ...
Page 43
... C components conveys a license under the Philips’ system provided the system conforms to the I 43 Preliminary specification TDA9321H (1) These products are not Philips Semiconductors 2 C patent to use the 2 C specification defined by ...
Page 44
... Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 5F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2451, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 60/14 MOO 11, Bangna Trad Road KM ...