M29F010B90N1T STMicroelectronics, M29F010B90N1T Datasheet

no-image

M29F010B90N1T

Manufacturer Part Number
M29F010B90N1T
Description
Manufacturer
STMicroelectronics
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
M29F010B90N1T
Manufacturer:
ST
0
July 1999
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice.
SINGLE 5V 10% SUPPLY VOLTAGE for
PROGRAM, ERASE and READ OPERATIONS
ACCESS TIME: 45ns
PROGRAMMING TIME
– 8 s per Byte typical
8 UNIFORM 16 Kbytes MEMORY BLOCKS
PROGRAM/ERASE CONTROLLER
– Embedded Byte Program algorithm
– Embedded Multi-Block/Chip Erase algorithm
– Status Register Polling and Toggle Bits
ERASE SUSPEND and RESUME MODES
– Read and Program another Block during
UNLOCK BYPASS PROGRAM COMMAND
– Faster Production/Batch Programming
LOW POWER CONSUMPTION
– Standby and Automatic Standby
100,000 PROGRAM/ERASE CYCLES per
BLOCK
20 YEARS DATA RETENTION
– Defectivity below 1 ppm/year
ELECTRONIC SIGNATURE
– Manufacturer Code: 20h
– Device Code: 20h
1 Mbit (128Kb x8, Uniform Block) Single Supply Flash Memory
Erase Suspend
Figure 1. Logic Diagram
A0-A16
PLCC32 (K)
W
G
E
32
17
1
V CC
M29F010B
V SS
PDIP32 (P)
M29F010B
PRELIMINARY DATA
TSOP32 (N)
8 x 20mm
8
DQ0-DQ7
AI02735
1/20

Related parts for M29F010B90N1T

M29F010B90N1T Summary of contents

Page 1

Mbit (128Kb x8, Uniform Block) Single Supply Flash Memory SINGLE 5V 10% SUPPLY VOLTAGE for PROGRAM, ERASE and READ OPERATIONS ACCESS TIME: 45ns PROGRAMMING TIME – per Byte typical 8 UNIFORM 16 Kbytes MEMORY BLOCKS PROGRAM/ERASE CONTROLLER ...

Page 2

M29F010B Figure 2A. PLCC Connections M29F010B DQ0 17 Figure 2C. PDIP Connections A16 2 31 A15 3 30 A12 ...

Page 3

... These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating condi- tions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant qual- ity documents. ...

Page 4

M29F010B Table 3. Block Addresses Size (Kbytes) Address Range 16 1C000h-1FFFFh 16 18000h-1BFFFh 16 14000h-17FFFh 16 10000h-13FFFh 16 0C000h-0FFFFh 16 08000h-0BFFFh 16 04000h-07FFFh 16 00000h-03FFFh BUS OPERATIONS There are five standard bus operations that control the device. These are Bus ...

Page 5

Table 4. Bus Operations Operation E V Bus Read IL V Bus Write IL Output Disable X Standby V IH Read Manufacturer V IL Code Read Device Code V IL Note Automatic ...

Page 6

... The other address bits IL IL may be set to either The Manufacturer IL IH Code for STMicroelectronics is 20h. The Device Code can be read using a Bus Read operation with and address bits may be set to either V Device Code for the M29F010B is 20h. The Block Protection Status of each block can be ...

Page 7

Table 5. Commands Command 1st Addr Data Read/Reset 3 555 AA Auto Select 3 555 AA Program 4 555 AA Unlock Bypass 3 555 AA Unlock Bypass Program Unlock Bypass Reset ...

Page 8

M29F010B Table 6. Program, Erase Times and Program, Erase Endurance Cycles ( – –40 to 125 C) A Parameter Chip Erase (All bits in the memory set to ‘0’) Chip Erase ...

Page 9

Table 7. Status Register Bits Operation Program Program During Erase Suspend Program Error Chip Erase Block Erase before timeout Non-Erasing Block Block Erase Non-Erasing Block Erase Suspend Non-Erasing Block Good Block Address Erase Error Faulty Block Address Note: Unspecified data ...

Page 10

M29F010B Figure 3. Data Polling Flowchart START READ DQ5 & DQ7 at VALID ADDRESS DQ7 YES = DATA NO NO DQ5 = 1 YES READ DQ7 DQ7 YES = DATA NO FAIL Erase Timer Bit (DQ3). The Erase Timer Bit ...

Page 11

Table 8. AC Measurement Conditions Parameter AC Test Conditions Load Capacitance ( Input Rise and Fall Times Input Pulse Voltages Input and Output Timing Ref. Voltages Figure 5. AC Testing Input Output Waveform High Speed 3V 0V Standard ...

Page 12

M29F010B Table 10. DC Characteristics ( – –40 to 125 C) A Symbol Parameter I Input Leakage Current LI I Output Leakage Current LO I Supply Current (Read) CC1 I Supply ...

Page 13

Table 11. Read AC Characteristics ( – –40 to 125 C) Symbol Alt Parameter Address Valid to Next t t AVAV RC Address Valid t t Address Valid to Output Valid ...

Page 14

M29F010B Table 12. Write AC Characteristics, Write Enable Controlled ( – –40 to 125 C) A Symbol Alt t t Address Valid to Next Address Valid AVAV Chip ...

Page 15

Table 13. Write AC Characteristics, Chip Enable Controlled ( – –40 to 125 C) A Symbol Alt t t Address Valid to Next Address Valid AVAV Write Enable ...

Page 16

M29F010B Table 14. Ordering Information Scheme Example: Device Type M29 Operating Voltage 10% CC Device Function 010B = 1 Mbit (128Kb x8), Uniform Block Speed ...

Page 17

Table 15. PLCC32 - 32 lead Plastic Leaded Chip Carrier, rectangular, Package Mechanical Data Symbol Typ 12.32 D1 11. 14.86 E1 13.89 E2 12. ...

Page 18

M29F010B Table 16. TSOP32 - 32 lead Plastic Thin Small Outline 20mm, Package Mechanical Data Symbol Typ 19.80 D1 18. 0. Figure 11. TSOP32 - 32 lead ...

Page 19

Table 17. PDIP32 - 32 lead Plastic DIP, 600 mils width, Package Mechanical Data Symbol Typ 1. 41.78 D2 38.10 E 15.24 E1 13.59 e1 2.54 eA 15.24 eB 15. ...

Page 20

... No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in lif e support devices or systems without express written approval of STMicroelectronics ...

Related keywords