HIP1012CB-T Intersil Corporation, HIP1012CB-T Datasheet
HIP1012CB-T
Available stocks
Related parts for HIP1012CB-T
HIP1012CB-T Summary of contents
Page 1
... HIP1012A has a minimum nominal over current threshold voltage of 50mV as compared to 100mV for the HIP1012. Ordering Information TEMP. o PART NUMBER RANGE ( C) PACKAGE HIP1012CB - SOIC HIP1012ACB HIP1012CB SOIC HIP1012ACB-T Tape and Reel Pinout HIP1012 (SOIC) TOP VIEW 1 3/12VS 14 3/12VISEN 3/12VG ...
Page 2
Simplified Schematic 12VIN C 20 GATE OPTIONAL R V FILTER DD C FILTER 20 C GATE 5VIN R SENSE 12VS R OC CLIM + - 2R 12VG FALLING - EDGE + DELAY 3X 18V ENABLE 18V ENABLE ...
Page 3
Pin Descriptions PIN # SYMBOL FUNCTION 1 3V/12VS 3.3 V/12V Source 2 3V/12VG 3.3V/12V Gate 3 V Chip Supply DD 4 MODE/ Power ON/ Reset PWRON1 Invokes 3.3V operation when shorted PWRON2 Power ON/ Reset 6 5VG ...
Page 4
Absolute Maximum Ratings ...
Page 5
Electrical Specifications V = 12V Unless Otherwise Specified (Continued) PARAMETER Gate Turn-On Time Gate Turn-On Current 3X Gate Discharge Current 5V Under Voltage Threshold 3.3V Under Voltage Threshold 3.3/5VG High Voltage SUPPLY CURRENT AND IO SPECIFICATIONS V Supply ...
Page 6
TABLE 1. R RESISTOR NOMINAL OC VTH ILIM 15k 10k 7.5k 4.99k NOTE: Nominal OC Vth = Rilim TABLE 2. C CAPACITOR NOMINAL TIME OUT PERIOD TIM 0.022 F 0.047 F 0.1 F NOTE: Nominal time-out period ...
Page 7
Typical Performance Curves 8.4 8.2 8.0 7.8 7.6 7.4 7.2 -40 -30 -20 - TEMPERATURE ( FIGURE 1. SUPPLY CURRENT 10.7 10.6 10.5 10.4 10.3 -40 -30 -20 - TEMPERATURE ( FIGURE ...
Page 8
Typical Performance Curves 17.36 17.34 12V VG 17.32 17.30 3.3V 17.28 17.26 -40 - TEMPERATURE ( C) FIGURE 7. 12V, 3/5V GATE DRIVE 54.5 54 Vth 53 Vth 53.0 52.5 ...
Page 9
Exploring and Using the HIP1012EVAL1 Board (Figure 13) The HIP1012EVAL1 is a flexible platform for a thorough evaluation of the HIP1012 dual power supply controller. This eval board comes in three separate parts allowing the evaluation of two principal configurations. ...
Page 10
HIP1012EVAL1 Board Components CEC1 3 /12VIN GND GND JP1 0 NOTE: Test point number equals HIP1012 pin number. CEF SW13 CEF 1,2,3 R102 SW14 LED2 CEF 4,5,6, ...
Page 11
BUS FIGURE 13. HIP1012EVAL1 EVAL BOARD GENERIC LOAD ...
Page 12
... SW14 and RL4 3.3V low load (1.6 ) LED2, LED3 Load “HOT” indicators BUS BOARD 12 HIP1012, HIP1012A COMPONENT DESCRIPTION Intersil Corporation, HIP1012CB Dual Power Controller Intersil Corporation, 30V, 30m , 6.3A Logic Level N-Channel MOSFET Mounting areas for additional 8 SOIC MOSFETs 100m 1 Metal Strip current sensing resistor ...
Page 13
HIP1012 Evaluation Circuit for Disk Drive Hot Swap Introduction The HIP1012EVAL2 is specifically designed to test and demonstrate hot swapping of disk drives onto passive 12V and 5V power buses using the HIP1012 Hot-Swap control IC. The small size of ...
Page 14
J2 12V GND JP1 10 1% GND 0 JP2 12VG CTIM PWRON1 PWRON2 PGOOD 5VG GND 0.01 F RF1K49157 Q1 FIGURE 14. ...
Page 15
... All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time with- out notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use ...