MCM63F733ATQ11 Motorola, MCM63F733ATQ11 Datasheet
MCM63F733ATQ11
Specifications of MCM63F733ATQ11
Related parts for MCM63F733ATQ11
MCM63F733ATQ11 Summary of contents
Page 1
... The PowerPC name is a trademark of IBM Corp., used under license therefrom. This document contains information on a new product. Specifications and information herein are subject to change without notice. REV 2 3/20/98 MOTOROLA FAST SRAM Motorola, Inc. 1998 Order this document by MCM63F733A/D MCM63F733A TQ PACKAGE TQFP and CASE 983A– ...
Page 2
... SBc SBd SE1 SE2 SE3 G MCM63F733A 2 FUNCTIONAL BLOCK DIAGRAM BURST COUNTER K2 CLR 2 17 ADDRESS REGISTER WRITE REGISTER a WRITE REGISTER b WRITE REGISTER c WRITE REGISTER d K2 ENABLE REGISTER 2 17 128K x 32 ARRAY DATA–IN REGISTER K DQa – DQd MOTOROLA FAST SRAM ...
Page 3
... DQc DQc DDQ DQc DQc DQd DQd V DDQ V SS DQd DQd DQd DQd DDQ DQd DQd NC MOTOROLA FAST SRAM PIN ASSIGNMENT 100 9695 ...
Page 4
... When ZZ is negated, the RAM remains in low power mode until it is commanded to READ or WRITE. Data integrity is maintained upon returning to normal operation Supply Core Power Supply. V DDQ Supply I/O Power Supply Supply Ground. NC — No Connection: There is no connection to the chip. Description MOTOROLA FAST SRAM ...
Page 5
... G must also remain negated at the completion of the write cycle to ensure proper write data hold times. ASYNCHRONOUS TRUTH TABLE Operation Read Read Write Deselected Selected LINEAR BURST ADDRESS TABLE (LBO = 1st Address (External) 2nd Address (Internal X00 X01 X10 X11 MOTOROLA FAST SRAM SE2 SE3 ADSP ADSC ADV ...
Page 6
... Max Unit Notes C/W 4 MOTOROLA FAST SRAM ...
Page 7
... Supply Voltage I/O Supply Voltage Input Low Voltage Input High Voltage Input High Voltage (I/O Pins) Output Low Voltage ( mA) Output High Voltage ( – – 1.0 V MOTOROLA FAST SRAM (Voltages Referenced Symbol DDQ IH2 V OL ...
Page 8
... — — TBD — TBD — — TBD — TBD — TBD 0 – 0.2 V. Min Typ Max Unit — — MOTOROLA FAST SRAM ...
Page 9
... Since the maximum test input edge rate is known and is given in the AC Test Conditions section of the data sheet as 1 V/ns, one can easily interpolate timing values to other reference levels. 5. This parameter is sampled and not 100% tested. 6. Measured at 200 mV from steady state. MOTOROLA FAST SRAM 1.25 V Output Timing Reference Level 0 to 2.5 V Output Load ...
Page 10
... OUTPUT Figure 3. Lumped Capacitive Load and Typical Derating Curve MCM63F733A 10 OUTPUT 1.25 V Figure 2. AC Test Load 2400 2200 2000 1800 1600 1400 1200 C L 1000 800 600 400 200 LUMPED CAPACITANCE (pF 100 MOTOROLA FAST SRAM ...
Page 11
... PULL–DOWN VOLTAGE (V) I (mA) MIN I (mA) MAX – 0 0.4 10 0.8 20 1.25 31 1.6 40 2.8 40 3.2 40 3.4 40 Figure 4. Typical Output Buffer Characteristics MOTOROLA FAST SRAM 2.9 2.5 2.3 – 105 – 105 – 105 1.25 – 83 – 75 0.8 – 40 – (a) Pull–Up for V DDQ = 2.5 V 3.6 3.135 2.8 – 120 – 120 1.65 – ...
Page 12
... MCM63F733A 12 MOTOROLA FAST SRAM ...
Page 13
... MOTOROLA FAST SRAM É É É É É É É É É É É É É ...
Page 14
... D E Q(C) Q(D) D(E) ORDERING INFORMATION (Order by Full Part Number) MCM 63F733A Blank = Trays Tape and Reel Speed ( ns ns) Package (TQ = TQFP) MCM63F733ATQ11 MCM63F733ATQ10R MCM63F733ATQ11R ( ADSC ADV SE1 SE2 LBO ...
Page 15
... D1 TIPS 0.20 (0.008) C A–B A –H– –C– SEATING PLANE 0.05 (0.002 VIEW AB MOTOROLA FAST SRAM PACKAGE DIMENSIONS TQ PACKAGE 100–PIN TQFP CASE 983A– TIPS 0.20 (0.008) C A–B D –D– E/2 –B– E1 ...
Page 16
... Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “ ...