UPG132G-E1 NEC, UPG132G-E1 Datasheet
UPG132G-E1
Available stocks
Related parts for UPG132G-E1
UPG132G-E1 Summary of contents
Page 1
... Digital hand-held cellular phone, WLAN ORDERING INFORMATION PART NUMBER PACKAGE PG132G-E1 8 pin plastic SSOP For evaluation sample order, please contact your local NEC sales office. ABSOLUTE MAXIMUM RATINGS (T Control Voltage Input Power Total Power Dissipation Operating Case Temperature Storage Temperature CAUTION: The IC must be handled with care to prevent static discharge because its circuit is composed of GaAs MES FET ...
Page 2
... PIN CONNECTION DIAGRAM (Top View SPDT SWITCH IC SERIES PRODUCTS PART P (1dB INS NUMBER (dBm) (dB) PG130GR +34 0.5 @1G PG131GR +30 0.6 @2G PG130G +34 0.5 @1G PG131G +30 0.6 @2G PG132G +30 0.6 @1G PG133G +25 0.6 @2G Remark: As for detail information of series products, please refer to each data sheet. APPLICATION EXAMPLE (PHS) ...
Page 3
... All other characteristics are measured in linear range. NOTE ON CORRECT USE • When the PG132G is used it is necessary to use DC blocking capacitor for No. 2 pin (OUT2), No. 5 pin (IN) and No. 7 pin (OUT1). The value of DC blocking capacitors should be chosen to accommodate the frequency of operation. ...
Page 4
TYPICAL CHARACTERISTICS ( ˚C) A Note This data is including loss of the test fixture. IN-OUT1 INSERTION LOSS vs. FREQUENCY + 2.0 V CONT1 V CONT2 dBm in + 1.0 0 – 1.0 – 2.0 ...
Page 5
IN-OUT2 INSERTION LOSS vs. FREQUENCY + 2 CONT1 CONT2 dBm in + 1.0 0 – 1.0 – 2.0 – 3.0 100 M 200 M 500 ...
Page 6
IN-OUT2 P vs Input Power - dBm in Internal Equivalent Circuit Between the GND pins and FETs of this IC, a capacitor ...
Page 7
... TEST BOARD IN 0.9 mm width R OUT1 V CONT1 TEST CIRCUIT V/+3 V CONT2 1 000 pF OUT2 NEC G132 R V OUT2 CONT2 C1, C2 PG132G 0.4 mm thickness teflon glass 000 V/0 V CONT1 OUT1 IN 7 ...
Page 8
APPLICATIONS Dependency on control voltage The input/output characteristics, insertion loss, and isolation characteristics hardly fluctuate dBm, even if the control voltage is changed in a range of +3 +5.0 V. When the IC is used ...
Page 9
Relation between Small Signal Characteristics and Control Voltage IN-OUT2 INSERTION LOSS vs. FREQUENCY +2 CONT1 CONT2 dBm in +1.0 0 –1.0 –2.0 –3.0 100 M 200 M 500 ...
Page 10
Relation between Control Voltage and Second Harmonic – +3.0 to +5.0 V CONT1 CONT2 GHz Non-modulated wave (CW) input – +3.0 V CONT1 V = +4.0 V CONT1 V ...
Page 11
Temperature characteristics Next, results from evaluating the temperature characteristics of the PG132G are shown. As shown, favorable characteristics are obtained in a range of T +0.0014 dB/˚C, indicating that the higher the temperature, the more the insertion loss. Temperature Characteristics ...
Page 12
PG132G TRUTH TABLE OF SWITCHING BY CONDITION OF CONTROL VOLTAGE + CONT2 8-PIN PLASTIC SHRINK SOP (175 mil) (Unit mm 3.0 MAX. 0.65 0.575 MAX CONT1 ...
Page 13
RECOMMENDED SOLDERING CONDITIONS This product should be soldered in the following recommended conditions. Other soldering methods and conditions than the recommended conditions are to be consulted with our sales representatives. [ PG132G] Soldering process Infrared ray reflow Package peak temperature: ...
Page 14
... Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices in “Standard“ unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact NEC Sales Representative in advance ...