MAX9750CETI+T Maxim Integrated Products, MAX9750CETI+T Datasheet - Page 22

• Manufacturer Part Number: MAX9750CETI+T
• Description: IC AMP AUDIO PWR 2.6W AB 28TQFN
• Manufacturer: Maxim Integrated Products
• Series: DirectDrive™r
• Type: Class ABr

Specifications of MAX9750CETI+T

• Output Type: 2-Channel (Stereo) with Stereo Headphones
• Max Output Power X Channels @ Load: 2.2W x 2 @ 3 Ohm; 110mW x 2 @ 16 Ohm
• Voltage - Supply: 4.5 V ~ 5.5 V
• Features: Depop, Short-Circuit and Thermal Protection, Shutdown, Volume Control
• Mounting Type: Surface Mount
• Package / Case: 28-TQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

reduces both ripple and output resistance. Lower
capacitance values can be used in systems with low
maximum output power levels. See the Output Power
vs. Charge-Pump Capacitance and Load Resistance
graph in the Typical Operating Characteristics .
The CPV
impedance of the power supply and reduces the
impact of the MAX9750/MAX9751/MAX9755’s charge-
pump switching transients. Bypass CPV
same value as C1, and place it physically close to
CPV
for a suggested layout).
An additional benefit of the MAX9750/MAX9751/
MAX9755 is the internally generated negative supply volt-
age (CPV
MAX9751/MAX9755 to provide the negative supply for
the headphone amplifiers. It can also be used to power
other devices within a design. Current draw from CPV
should be limited to 5mA, exceeding this affects the oper-
ation of the headphone amplifier. A typical application is
a negative supply to adjust the contrast of LCD modules.
When considering the use of CPV
note that the charge-pump voltage of CPV
proportional to CPV
The charge-pump output impedance plot appears in
the Typical Operating Characteristics .
Proper layout and grounding are essential for optimum
performance. Use large traces for the power-supply
inputs and amplifier outputs to minimize losses due to
parasitic trace resistance, as well as route head away
from the device. Good grounding improves audio per-
formance, minimizes crosstalk between channels, and
prevents any switching noise from coupling into the
audio signal. Connect CPGND, PGND and GND
2.6W Stereo Audio Power Amplifiers and
DirectDrive Headphone Amplifiers
22
DD
______________________________________________________________________________________
and PGND (refer to the MAX9750 Evaluation Kit
DD
SS
bypass capacitor (C3) lowers the output
). CPV
Powering Other Circuits from a
DD
SS
CPV
and is not a regulated voltage.
is used by the MAX9750/
Layout and Grounding
DD
Bypass Capacitor (C3)
Negative Supply
SS
in this manner,
DD
SS
with C3, the
is roughly
SS
together at a single point on the PC board. Route
CPGND and all traces that carry switching transients
away from GND, PGND, and the traces and compo-
nents in the audio signal path.
Connect all components associated with the charge
pump (C2 and C3) to the CPGND plane. Connect V
and CPV
pump capacitors (C1, C2, and C3) as close to the
device as possible. Bypass HPV
0.1µF capacitor to GND. Place the bypass capacitors
as close to the device as possible.
Use large, low-resistance output traces. As load imped-
ance decreases, the current drawn from the device out-
puts increase. At higher current, the resistance of the
output traces decrease the power delivered to the load.
For example, when compared to a 0Ω trace, a 100mΩ
trace reduces the power delivered to a 4Ω load from
2.1W to 2W. Large output, supply, and GND traces also
improve the power dissipation of the device.
The MAX9750/MAX9751/MAX9755 thin QFN package
features an exposed thermal pad on its underside. This
pad lowers the package’s thermal resistance by provid-
ing a direct heat conduction path from the die to the
printed circuit board. Connect the exposed thermal
pad to GND by using a large pad and multiple vias to a
GND plane on the bottom of the PCB.
SS
together at the device. Place the charge-
DD
and PV
DD
with a
SS