V24B12C200BN2 Vicor Corporation, V24B12C200BN2 Datasheet
V24B12C200BN2
Related parts for V24B12C200BN2
V24B12C200BN2 Summary of contents
Page 1
RoHS Compliant (with pin option) DC input range • Operation 75% power • after startup Input surge withstand for 100 ms • • DC output: 3.3 ...
Page 2
Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature, unless otherwise specified. All temperatures refer to the operating temperature at the center of the baseplate. MODULE INPUT SPECIFICATIONS Parameter Min Operating input ...
Page 3
MODULE CONTROL SPECIFICATIONS Parameter Min PRIMARY SIDE (PC = Primary Control Parallel) PC bias voltage 5.50 current limit 1.5 PC module disable 2.3 PC module enable delay PC module alarm PC resistance 0.9 PR emitter amplitude 5.7 PR ...
Page 4
MODULE SPECIFIC OPERATING SPECIFICATIONS 3.3 Vout, 150 W (e.g. V24B3V3C150BL) Parameter Min Efficiency 77 Ripple and noise Output OVP setpoint 4.14 Dissipation, standby Load regulation Load current 0 Current limit 46.4 Short circuit current 31.8 3.3 Vout, 100 W (e.g. ...
Page 5
MODULE SPECIFIC OPERATING SPECIFICATIONS (CONT.) 12 Vout, 200 W (e.g. V24B12C200BL) Parameter Min Efficiency 85 Ripple and noise Output OVP setpoint 13.8 Dissipation, standby Load regulation Load current 0 Current limit 17 Short circuit current 11.6 12 Vout, 150 W ...
Page 6
MODULE SPECIFIC OPERATING SPECIFICATIONS 24 Vout, 150 W (e.g. V24B24C150BL) Parameter Min Efficiency 86.5 Ripple and noise Output OVP setpoint 27.1 Dissipation, standby Load regulation Load current 0 Current limit 6.37 Short circuit current 3 28 Vout, 200 W (e.g. ...
Page 7
MODULE SPECIFIC OPERATING SPECIFICATIONS (CONT.) 48 Vout, 200 W (e.g. V24B48C200BL) Parameter Min Efficiency 86.5 Ripple and noise Output OVP setpoint 53.8 Dissipation, standby Load regulation Load current 0 Current limit 4.25 Short circuit current 2.91 48 Vout, 150 W ...
Page 8
The module may be disabled by pulling PC below 2.3 V with respect to the –Input. This may be done with an open collector transistor, relay, or optocoupler. Multiple converters may be disabled with a single transistor or relay either ...
Page 9
The output voltage of the converter can be adjusted or programmed via fixed resistors, potentiometers or voltage DACs. See Figures 7 and 8. +Out +S Error SC Amp –S 1kΩ 0.033 μF –Out 1.23V 1,000 Vout R (ohms ...
Page 10
The PR pin supports paralleling for increased power with N+1 (N+M) redundancy and phased array capability. Modules of the same input voltage, output voltage, and power level will current share if all PR pins are suitably interfaced. Compatible interface architectures ...
Page 11
The +Out and –Out power buses +In +Out should be designed to minimize +S and balance parasitic impedance PC +S Module SC from each module output to the 1 PR –S –S load. –In –Out • The +Sense pins ...
Page 12
Converter Pins No. Function Label 1 +In + Primary 2 PC Control 3 Parallel PR 4 –In – 5 –Out – 6 –Sense –S Secondary 7 SC Control 8 +Sense +S 9 +Out + Figure 13 — Module outline 0.062 ...
Page 13
Vicor products are guaranteed for two years from date of shipment against defects in material or workmanship when in normal use and service. This warranty does not extend to products subjected to misuse, accident, or improper application or maintenance. Vicor ...