SC9102D Silan, SC9102D Datasheet
SC9102D
Related parts for SC9102D
SC9102D Summary of contents
Page 1
... Flash function (RESET pause time (3.6ms) Flash time (600/100ms) Flash pause time (0ms) * Packaged in 18-pin plastic DIP BLOCK DIAGRAM HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn SC9102C/D DIP-18-300-2.54 ORDERING INFORMATION Part Package SC9102C DIP-18-300-2.54 SC9102D DIP-18-300-2.54 REV:2.0 2004.08.03 Page ...
Page 2
... Memory retension Tone I Pulse, OFF-HOOK, Keypad OP entry, no load ON-HOOK No keypad I S entry ,no load V =1.0V DD SC9102C #/RD RD Flash Time SC9102D SC9102C 600ms 100ms 100ms 600ms 600ms 600ms , unless otherwise specified) ss 6.0 +0.3 DD 500 =3.579545MHz, unless otherwise Min. Typ. Max. 2.0 5.5 1.0 5.5 0.6 2 ...
Page 3
... Minimum Intertone Pause Time Note: 1. Vn: Input voltage of any keyboard scanning pin (Row group, Column group) 2. Distortion (dB) = 20log Row group and Column group signal L H V1,V2… ,Vn: Harmonic signal (BW = 300Hz~3500Hz) HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn Conditions =12.0V I mth ...
Page 4
... ACTUAL FREQUENCY OUTPUT Keyboard Scanning Pin PIN CONFIGURATION HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn (f =3.579545MHz) OSC Standard(Hz) Output 697 770 852 941 1209 1336 1477 ...
Page 5
... ON-HOOK state, this pin must be pulled “ high” in order to HKS 5 disable the dialing operation and decrease the power consumption. *When in OFF-HOOK state, the operation. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn Description is “ LOW” valid key entry is defined by related Row & Column Row Column ...
Page 6
... Digit Dialing Procedure : D1, D2… Dial out : Dt1, Dt2… , Dtn (in Tone mode) Dial out : Dp1, Dp2,… , Dpn (in Pulse mode) LNB : D1, D2… HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn SC9102C/D Description MODE Dialing mode V Pulse mode DD Open Pulse mode V Tone mode SS REV:2 ...
Page 7
... Procedure D1, D2… … Dial out Dt1, Dt2,… , Dtn , t Dial out Dp1, Dp2,… , Dpn , t LNB C1, C2 … HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn , … , Dpn (in Pulse mode Dt9, Dt10… , Dtn PT , Ct1 … , Ctn (in Tone mode Cp1 … , Cpn (in Pulse mode) ...
Page 8
... DTMF signal Whether keyboard is pushed refer to the TONE mode time diagram. 2. Sink current Isink=I/(1-Duty Cycle the net DC current measured from ampere meter. 3. R*, C* mean other column and row. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com. 1/2 2 ...
Page 9
... TIMING DIAGRAMS HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn SC9102C/D REV:2.0 2004.08.03 Page ...
Page 10
... TIMING DIAGRAMS (continued) HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn SC9102C/D REV:2.0 2004.08.03 Page ...
Page 11
... TIMING DIAGRAMS (continued) HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn SC9102C/D REV:2.0 2004.08.03 Page ...
Page 12
... TIMING DIAGRAMS (continued) HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn SC9102C/D REV:2.0 2004.08.03 Page ...
Page 13
... TYPACAL APPLICATION CIRCUIT CHIP TOPOGRAPHY HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn 2 Chip size: 1.35 x 1.33 mm SC9102C/D REV:2.0 2004.08.03 Page ...
Page 14
... P3 -539 539 21 191 362 529 540.5 Note: The original point of the coordinate is the die center. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com. Pad No. 276.0 10 109.0 11 -266.0 12 -453.5 13 -528.0 14 -528.0 15 -381.5 16 8.5 17 176.4 18 SC9102C/D ...
Page 15
... Persons at a work bench should be earthed via a wrist strap. Equipment cases should be earthed. All tools used during assembly, including soldering tools and solder baths, must be earthed. MOS devices should be packed for dispatch in antistatic/conductive containers. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn 2.54 1.52 23.12±0.3 ...