ATxmega32D4 Atmel Corporation, ATxmega32D4 Datasheet - Page 93

• Manufacturer Part Number: ATxmega32D4
• Manufacturer: Atmel Corporation

Specifications of ATxmega32D4

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Speed: No
• Usb Interface: No
• Spi: 4
• Twi (i2c): 2
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 200
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 14
• Input Capture Channels: 14
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

9.7.3
8210B–AVR–04/10
STATUS – Watchdog Status Register
Table 9-2.
• Bit 1 - WEN: Watchdog Window Mode Enable
This bit enables the Watchdog Window Mode. In order to change this bit the WCEN bit in
”WINCTRL – Window Mode Control Register” on page 92
time. This bit is protected by the Configuration Change Protection mechanism, for detailed
description refer to
• Bit 0 - WCEN: Watchdog Window Mode Change Enable
This bit enables the possibility to change the configuration of the
Control Register” on page
to one at the same time for the changes to take effect. This bit is protected by the Configuration
Change Protection mechanism, but not protected by the WDT lock fuse.
• Bit 7:1 - Reserved
These bits are reserved and will always be read as zero. For compatibility with future devices,
always write these bits to zero when this register is written.
• Bit 0 - SYNCBUSY
When writing to the CTRL or WINCTRL registers, the WDT needs to be synchronized to the
other clock domains. During synchronization the SYNCBUSY bit will be read as one. This bit is
automatically cleared after the synchronization is finished. Synchronization will only take place
when the ENABLE bit for the Watchdog Timer is set.
Bit
+0x02
Read/Write
Initial Value
WPER[3:0]
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
Watchdog closed window periods (Continued)
R
7
–
0
”Configuration Change Protection” on page
R
6
–
0
92. When writing a new value to this register, this bit must be written
Group Configuration
R
5
–
0
500CLK
1KCLK
2KCLK
4KCLK
8KCLK
R
4
–
0
3
–
R
0
must be written to one at the same
2
–
R
0
Typical closed window periods
12.
”WINCTRL – Window Mode
R
1
–
0
Reserved
Reserved
Reserved
Reserved
Reserved
0.5 s
1.0 s
2.0 s
4.0 s
8.0 s
SYNCBUSY
XMEGA D
R
0
0
STATUS
93