AD5325 Analog Devices, AD5325 Datasheet - Page 21

no-image

AD5325

Manufacturer Part Number
AD5325
Description
Manufacturer
Analog Devices
Datasheet

Specifications of AD5325

Resolution (bits)
12bit
Dac Update Rate
125kSPS
Dac Settling Time
8µs
Max Pos Supply (v)
+5.5V
Single-supply
Yes
Dac Type
Voltage Out
Dac Input Format
I2C/Ser 2-wire,Ser

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD5325ARMZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD5325BRM-REEL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD5325BRMZ
Manufacturer:
CIRRUS
Quantity:
46
Part Number:
AD5325BRMZ
Manufacturer:
AD
Quantity:
16
Part Number:
AD5325BRMZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD5325BRMZ-REEL7
Manufacturer:
2WIRE
Quantity:
12 233
Part Number:
AD5325BRMZ-REEL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD5305/AD5315/AD5325 AS A DIGITALLY
PROGRAMMABLE WINDOW DETECTOR
A digitally programmable upper/lower limit detector using two
of the DACs in the AD5305/AD5315/AD5325 is shown in
Figure 39. The upper and lower limits for the test are loaded to
DAC A and DAC B, which, in turn, set the limits on the CMP04. If
the signal at the V
an LED indicates the fail condition. Similarly, DAC C and DAC D
can be used for window detection on a second V
V
COARSE AND FINE ADJUSTMENT USING THE
AD5305/AD5315/AD5325
Two of the DACs in the AD5305/AD5315/AD5325 can be paired
together to form a coarse and fine adjustment function, as shown
in Figure 40. DAC A is used to provide the coarse adjustment
while DAC B provides the fine adjustment. Varying the ratio of
R1 and R2 changes the relative effect of the coarse and fine
adjustments. With the resistor values and external reference shown
in Figure 40, the output amplifier has unity gain for the DAC A
output. As a result, the output range is 0 V to 2.5 V − 1 LSB. For
DAC B, the amplifier has a gain of 7.6 × 10
range equal to 19 mV. Similarly, DAC C and DAC D can be
paired together for coarse and fine adjustment.
The circuit is shown with a 2.5 V reference, but reference
voltages up to V
a rail-to-rail output swing.
AD780/REF192
WITH V
SCL
REF
DIN
5V
EXT
REF
GND
V
1
1
ADDITIONAL PINS OMITTED FOR CLARITY.
IN
DD
V
ADDITIONAL PINS OMITTED FOR CLARITY.
OUT
= 5V
0.1µF
REFIN
SDA
SCL
0.1µF
AD5325
AD5305/
AD5315/
1µF
DD
10µF
GND
IN
1/2
Figure 40. Coarse/Fine Adjustment
can be used. The op amps indicated allows
input is not within the programmed window,
10µF
Figure 39. Window Detection
V
1
V
V
DD
REFIN
OUT
OUT
A
AD5325
B
AD5305/
AD5315/
V
DD
GND
1/2
V
DD
= 5V
V
IN
V
V
1
OUT
OUT
51.2kΩ
A
B
CMP04
R3
1/2
51.2kΩ
390Ω
R1
R2
−3
, giving DAC B a
390Ω
R4
FAIL
1kΩ
PASS/FAIL
1/6 74HC05
IN
5V
signal.
AD820/
OP295
PASS
V
1kΩ
OUT
Rev. G | Page 21 of 24
POWER SUPPLY DECOUPLING
In any circuit where accuracy is important, careful
consideration of the power supply and ground return layout
helps to ensure the rated performance. The printed circuit
board on which the AD5305/AD5315/AD5325 is mounted
should be designed so that the analog and digital sections are
separated and confined to certain areas of the board. If the
AD5305/AD5315/AD5325 is in a system where multiple devices
require an AGND-to-DGND connection, the connection
should be made at one point only. The star ground point should
be established as close as possible to the device. The AD5305/
AD5315/AD5325 should have ample supply bypassing of 10 μF
in parallel with 0.1 μF on the supply located as close to the
package as possible, ideally right up against the device. The
10 μF capacitors are the tantalum bead type. The 0.1 μF
capacitor should have low effective series resistance (ESR) and
effective series inductance (ESI), such as the common ceramic
types that provide a low impedance path to ground at high
frequencies to handle transient currents due to internal logic
switching.
The power supply lines of the AD5305/AD5315/AD5325
should use as large a trace as possible to provide low impedance
paths and reduce the effects of glitches on the power supply
line. Fast switching signals such as clocks should be shielded
with digital ground to avoid radiating noise to other parts of the
board, and should never be run near the reference inputs. A
ground line routed between the SDA and SCL lines helps reduce
crosstalk between them (not required on a multilayer board as
there is a separate ground plane, but separating the lines does help).
Avoid crossover of digital and analog signals. Traces on
opposite sides of the board should run at right angles to each
other. This reduces the effects of feedthrough through the
board. A microstrip technique is by far the best, but is not
always possible with a double-sided board. In this technique,
the component side of the board is dedicated to ground plane
while signal traces are placed on the solder side.
AD5305/AD5315/AD5325

Related parts for AD5325