MAX9892ELT+T Maxim Integrated Products, MAX9892ELT+T Datasheet - Page 5

• Manufacturer Part Number: MAX9892ELT+T
• Description: IC ELIMINATOR CLICK/POP 6UDFN
• Manufacturer: Maxim Integrated Products
• Type: Audio Suppressorr

Specifications of MAX9892ELT+T

• Applications: Portable Audio, Telephony
• Mounting Type: Surface Mount
• Package / Case: 6-µDFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The MAX9892 is the second-generation click-and-pop
eliminator designed to be used with conventional head-
phone amplifiers. The MAX9892 works by adding a low-
impedance current path from the headphone side of
the DC-blocking capacitor to ground. Drive MUTE low
when turning off the amplifier, and high when enabling
the amplifier. A short turn-on time allows the switches in
the MAX9892 to close before the DC-blocking capaci-
tors have significantly discharged, eliminating clicks
and pops at amplifier turn-off. An adjustable turn-off
time allows the delay to be set to mask all clicks and
pops during amplifier turn-on.
The MAX9892 features a SET input that allows the turn-
off time to be adjusted from 1ms to 1000ms to match
the click-and-pop profile of the amplifier startup. The
value of an external capacitor sets the switch open
delay, as shown in the following equation:
When the headphone amplifier is enabled, the
MAX9892 automatically waits the set delay time before
opening the analog switches. This allows amplifier turn-
on click and pop to be eliminated.
The MAX9892 operates from 1.7V to 3.6V supply volt-
age. The inputs, INL and INR, accept voltage swings
from V
headphone is ground biased, meaning that the signal
swings just as much negative as positive. Since the
MAX9892 input voltage is limited to V
negative side, the voltage on V
to pass the audio signal when the switch is open
(Figure 2).
A voltage-divider can be used to scale down an avail-
able supply voltage as shown in Figure 3. The voltage-
divider allows the creation of a supply voltage for the
MAX9892 that is low enough to allow the negative por-
tion of the audio signal to pass. When using large resis-
tances for the voltage-divider, the supply current
affects what resistors to use. Select R
to 1MΩ for a given supply voltage. Use the following
equation to calculate the R
DD
to V
Shunt Mode Audio Click-and-Pop Eliminator
t
DD
ON
Applications Information
R
- 5.5V. The audio signal applied to a
(ms) = 0.02 x C
_______________________________________________________________________________________
1
=
Setting the Supply Voltage
(
V
Detailed Description
Setting the Turn-Off Time
AMP
I
2
1
+
:
I
−
DD
V
DD
DD
SET
)
must be set properly
(pF)
DD
2
between 10kΩ
- 5.5V on the
where V
I
ence to GND, the MAX9892 supply can be set from 2V
to 3.5V.
A series resistor (R
Operating Circuit , is necessary to achieve optimal click-
and-pop reduction. See the Click and Pop vs. R
graph in the Typical Operating Characteristics for
details on how much click-and-pop reduction to expect
for a given series resistor.
Bypass V
bypass capacitor should be positioned as close as
possible to V
solid system ground plane to ensure optimum perfor-
mance.
Refer to the MAX9892 Evaluation Kit for a proven PCB
layout.
Figure 2. Proper Supply Selected for a Given Input Signal.
A: Supply Voltage with a Large Signal;
B: Supply Voltage with a Small Signal
2
IN_
IN_
is the current through R
V
V
DD
DD
- 5.5V
- 5.5V
AMP
V
V
DD
DD
DD
A
B
is the supply voltage of the amplifier, and
to GND with a 0.1µF capacitor. The 0.1µF
DD
. Minimize trace length from GND to
SERIES
Selecting Series Resistors
2
Layout Considerations
. For a signal of ±2V in refer-
), as shown in the Typical
SERIES
GND
GND
5