LM393WDT Rohm Semiconductor, LM393WDT Datasheet - Page 7

• Manufacturer Part Number: LM393WDT
• Description: IC COMPARATOR DUAL 0.4MA 8-SOIC
• Manufacturer: Rohm Semiconductor
• Series: Signaturer
• Type: General Purposer

Specifications of LM393WDT

• Number Of Elements: 2
• Output Type: CMOS, MOS, Open-Collector, TTL
• Voltage - Supply: 2 V ~ 36 V, ±1 V ~ 18 V
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LM393WDTTR

Derating Curve
1) Unused circuits
2) Input terminal voltage
3) Power supply (single / dual)
4) Power dissipation Pd
5) Short-circuit between pins and erroneous mounting
6) Terminal short-circuits
7) Operation in a strong electromagnetic field
8) Radiation
9) IC handing
10) Board inspection
Precautions
When there are unused circuits it is recommended that they be
connected as in Fig. 6, setting the non-inverting input terminal
to a potential within the in-phase input voltage range (VICM).
Applying Vcc
deterioration of the electrical characteristics or destruction, irrespective
of the supply voltage. However, this does not ensure normal circuit operation.
Please note that the circuit operates normally only when the input voltage is
within the common mode input voltage range of the electric characteristics.
The op-amp operates when the specified voltage supplied is between Vcc
and Vcc
Using the unit in excess of the rated power dissipation may cause deterioration in the electrical characteristics due to a rise in chip temperature, including
reduced current capability. Therefore, please take into consideration the power dissipation (Pd) under actual operating conditions and apply a sufficient
margin in thermal design. Refer to the thermal derating curves for more information.
Incorrect mounting may damage the IC. In addition, the presence of foreign particles between the outputs, the output and the power supply, or the output and
Vcc
When output and Vcc
Operation in a strong electromagnetic field may cause malfunctions.
This IC is not designed to withstand radiation.
Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuations in the electrical characteristics due to piezoelectric (piezo)
effects.
Connecting a capacitor to a pin with low impedance may stress the IC. Therefore, discharging the capacitor after every process is recommended. In addition,
when attaching and detaching the jig during the inspection phase, ensure that the power is turned OFF before inspection and removal. Furthermore, please
take measures against ESD in the assembly process as well as during transportation and storage.
-
may result in IC destruction.
-
. Therefore, the single supply op-amp can be used as a dual supply op-amp as well.
-
+ 36[V] to the input terminal is possible without causing
+
terminals are shorted, excessive output current may flow, resulting in undue heat generation and, subsequently, destruction.
1000
800
600
400
200
0
LM393DT/PT/ST/WDT/WPT
25
Ambient temperature : Ta [ ]
500[mV] TSSOP8 (*3)
470[mV] Mini SO8 (*4)
450[mV] SO package8 (*5)
50
75
Power Dissipation
70[ ]
SO Package8 (*5)
TSSOP8 (*3)
Mini SO8 (*4)
ja = (Tj-Ta)/Pd[ /W]
100
Package
125
Fig.5 Derating Curve
150
7/8
Pd[W]
+
450
500
470
ja [ /W]
3.76
3.6
4.0
1000
800
600
400
200
0
25
Ambient temperature : Ta [ ]
SIGNATURE SERIES LM2903/2901/393/339 family
500[mV] TSSOP8 (*3)
470[mV] Mini SO8 (*4)
450[mV] SO package8 (*5)
LM2903DT/PT
50
Fig.6 Disable circuit example
These Products are designed and produced by ROHM.
75
100
Vcc
Vcc
125
+
-
125[ ]
150