DS1677 Maxim, DS1677 Datasheet - Page 3

• Manufacturer Part Number: DS1677
• Description: The DS1677 portable system controller is a circuit that incorporates many of the functions necessary for low-power portable products integrated into one chip
• Manufacturer: Maxim

PIN DESCRIPTION
15, 16
17, 18
PIN
14,
10
11
12
13
19
20
1
2
3
4
5
6
7
8
9
NAME
X2, X1
SCLK
AIN2,
AIN1,
AIN0
GND
V
V
CEO
N.C.
PFO
RST
CEI
INT
V
PFI
I/O
CS
ST
BAT
CCO
CC
Battery Input for Standard 3V Lithium Cell or Other Energy Source. UL recognized to
ensure against reverse charging when used with a lithium battery. Go to
ic.com/qa/info/ul/.
External SRAM Power Supply Output. This pin is internally connected to V
within nominal limits. However, during power-fail V
V
Serial Clock Input. Used to synchronize data movement on the serial interface.
Data Input/Output. This pin is the bidirectional data pin for the 3-wire interface.
Chip Select. Must be asserted high during a read or a write for communication over the 3-
wire serial interface. CS has an internal 40k pulldown resistor.
RAM Chip-Enable In. Must be driven low to enable the external RAM.
RAM Chip-Enable Out Low. Active-low chip-enable output for low-order SRAM byte.
No Connection
Interrupt Output. This pin is an active-high output that can be used as an interrupt input to
a microprocessor. The INT output remains high as long as the status bit causing the
interrupt is present and the corresponding interrupt-enable bit is set. The INT pin operates
when the DS1677 is powered by V
Ground. DC power is provided to the device on this pin.
Active-Low Power-Fail Output. This pin goes low and sinks current when PFI is less than
1.25V; otherwise this pin remains high.
Active-Low Power-Fail Input. When PFI is less than 1.25V, PFO goes low; otherwise
Active-Low Reset. The RST pin functions as a microprocessor reset signal. This pin is
driven low 1) when V
timed out; 3) during the power up reset period; and 4) in response to a pushbutton reset.
The RST pin also functions as a pushbutton reset input. When the RST pin is driven low,
the signal is debounced and timed such that a RST signal of at least 250ms is generated.
This pin has an open-drain output with an internal 47k pullup resistor.
Analog Inputs. These pins are the three analog inputs for the 3-channel ADC.
Connections for Standard 32.768kHz Quartz Crystal. For greatest accuracy, the DS1670
must be used with a crystal that has a specified load capacitance of 6pF. There is no need
for external capacitors or resistors. Note: X1 and X2 are very high-impedance nodes. It is
recommended that they and the crystal be guard-ringed with ground and that high
frequency signals be kept away from the crystal area. For more information on crystal
selection and crystal layout considerations, refer to Application Note 58: Crystal
Considerations with Dallas Real Time Clocks. The DS1677 does not function without a
crystal.
+5.0V Input DC Power
Active-Low Strobe Input. The strobe input pin is used with the watchdog timer. If the ST
pin is not driven low within the watchdog time period, the RST pin is driven low.
PFO
BAT
pin. Switchover occurs when V
remains high. Connect PFI to GND or V
CC
is outside of nominal limits; 2) when the watchdog timer has
3 of 18
CC
CC
or V
FUNCTION
drops below the lower of V
BAT
.
CC
when not used.
CCO
is internally connected to the
BAT
or 2.7V.
www.maxim-
CC
when V
CC
is