MAX4386E Maxim, MAX4386E Datasheet
MAX4386E
Available stocks
Related parts for MAX4386E
MAX4386E Summary of contents
Page 1
... International ESD Standards: ±15kV IEC 1000-4-2 Air-Gap Discharge, ±8kV IEC 1000-4-2 Contact Discharge, and the ±15kV Human Body Model. The MAX4385E/MAX4386E operate from a single 5V supply with a common-mode input voltage range that extends beyond V . The MAX4385E/MAX4386E con- EE sume only 5 ...
Page 2
... Lead Temperature (soldering, 10s) .................................+300°C = ∞ / 2.2µ BYPASS CONDITIONS Guaranteed by CMRR +25° -40°C to +85°C A MAX4386E VOS Differential mode (-1V ≤ V ≤ +1V Common mode (-0.2V ≤ V ≤ +2.75V 0.2V ≤ V ≤ 2.25V 0.25V ≤ ...
Page 3
Low-Cost, 230MHz, Single/Quad Op Amps with Rail-to-Rail Outputs and ±15kV ESD Protection DC ELECTRICAL CHARACTERISTICS (continued 5V / OUT Typical values are +25°C.) (Note ...
Page 4
Low-Cost, 230MHz, Single/Quad Op Amps with Rail-to-Rail Outputs and ±15kV ESD Protection ( 1.5V 1V/ VCL SMALL-SIGNAL GAIN vs. FREQUENCY 100mV OUT P-P 3 ...
Page 5
Low-Cost, 230MHz, Single/Quad Op Amps with Rail-to-Rail Outputs and ±15kV ESD Protection ( 1.5V VCL DISTORTION vs. VOLTAGE SWING 5MHz O - 1V/V VCL ...
Page 6
Low-Cost, 230MHz, Single/Quad Op Amps with Rail-to-Rail Outputs and ±15kV ESD Protection ( 1.5V 1V/ VCL LARGE-SIGNAL PULSE RESPONSE A = 2V/V VCL R = 200Ω F ...
Page 7
... Rail-to-Rail Outputs and ±15kV ESD Protection ( 1.5V VCL INPUT OFFSET VOLTAGE vs. TEMPERATURE 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1 0.5 0 -0.5 -50 - TEMPERATURE (°C) PIN MAX4385E MAX4386E SOT23 SO/TSSOP 1 — — 4 — — 1 — 2 — 3 — 5 — 6 — 7 — 8 — 9 — 10 — 12 — ...
Page 8
... Low-Cost, 230MHz, Single/Quad Op Amps with Rail-to-Rail Outputs and ±15kV ESD Protection Detailed Description The MAX4385E/MAX4386E are single/quad, 5V, rail-to- rail, voltage-feedback amplifiers that employ current- feedback techniques to achieve 450V/µs slew rates and 230MHz bandwidths. High ±15kV ESD protection guards against unexpected discharge. Excellent har- ...
Page 9
... P-P Output Capacitive Loading and Stability The MAX4385E/MAX4386E are optimized for AC perfor- mance and do not drive highly reactive loads, which decreases phase margin and may produce excessive ringing and oscillation. Figure 2 shows a circuit that eliminates this problem. Figure graph of the Optimal Isolation Resistor ( ...
Page 10
... The IEC 1000-4-2 standard covers ESD testing and performance of finished equipment; it does not specifi- cally refer to ICs. The MAX4385E/MAX4386E enable the design of equipment that meets the highest level (Level 4) of IEC 1000-4-2 without the need for additional ESD protection components. The major difference between tests done using the Human Body Model and IEC 1000- 4-2 is higher peak current in IEC 1000-4-2 ...
Page 11
... INA- 2 INA+ 3 MAX4386E INB+ 5 INB- 6 OUTB 7 TSSOP/SO ______________________________________________________________________________________ DEVICE UNDER TEST 0.7ns TO 1ns Figure 10. IEC 1000-4-2 ESD Generator Current Waveform MAX4385E TRANSISTOR COUNT: 124 MAX4386E TRANSISTOR COUNT: 264 14 OUTD 13 IND- 12 IND INC+ 9 INC- 8 OUTC I 100% 90% 10% t 30ns ...
Page 12
... Low-Cost, 230MHz, Single/Quad Op Amps with Rail-to-Rail Outputs and ±15kV ESD Protection (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages.) 12 ______________________________________________________________________________________ Package Information PACKAGE OUTLINE, SOT-23, 5L ...
Page 13
... A1 FRONT VIEW Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 © ...