MAX4362 Maxim, MAX4362 Datasheet
MAX4362
Related parts for MAX4362
MAX4362 Summary of contents
Page 1
... Spurious-free dynamic range (SFDR) at full output power is typically -75dBC at 100kHz. The MAX4361 is a differential IN/differential OUT driver with a fixed gain of 3.1V/V. The MAX4362 is a dual amplifier with shutdown intended for use as a differen- tial IN/differential OUT driver with gain set with external resistors ...
Page 2
... MAX4363, measured at = ∞ V+ (TX), R SHDN = 5V L SHDN = 0 MAX4363, measured at = ∞ V+ (RX), R SHDN = 5V L DMT modulation CAP modulation MAX4361 (0.7V ≤ V ≤ (V+) - 0.7V) OUT MAX4362/MAX4363 (0.7V ≤ V ≤ (V+) - 0.7V) OUT 100kHz 7.1V OUT(DIFF 100kHz 7.1V OUT(DIFF) P-P Inferred from Output Voltage Swing test MAX4361 MAX4362/MAX4363 MAX4361 MAX4362/MAX4363 ...
Page 3
... Inferred from Output Voltage Swing test (V 100Ω (V MAX4362/MAX4363 R = 12.5Ω (V MAX4361 12.5Ω -20°C to 85° MAX4361 MAX4362/MAX4363 SHDN = 0 or SHDN = 1MHz MAX4361 MAX4362/MAX4363 7.1V step OUT(DIFF) P-P MAX4361 V = 7.1V OUT(DIFF) P-P MAX4362/MAX4363, S step 100kHz to 1 ...
Page 4
... Note 2: Implied by worst-case output-voltage swing (V ✕ 10log((250 (V Driver OUT(DIFF) Note 3: Guaranteed by design. Note 4: May exceed absolute maximum ratings for power dissipation if unit is subject to full-scale sinusoids for long periods (see Applications Information section). 4 _______________________________________________________________________________________ = unless otherwise noted. Typical values specified at A ...
Page 5
ADSL Drivers/Receivers for Customer Premise (V+ = 5V, GND = 2.5V 12.5Ω, SHDN = DRIVER DIFFERENTIAL DISTORTION vs. FREQUENCY - 7.2V OUT P - ...
Page 6
ADSL Drivers/Receivers for Customer Premise Equipment (V+ = 5V, GND = 2.5V 12.5Ω, SHDN = RECEIVER DIFFERENTIAL DISTORTION vs. FREQUENCY - OUT P -50 R ...
Page 7
... ADSL Drivers/Receivers for Customer Premise MAX4361 PIN NAME 1, 4 GND 2 IN+ 3 IN- 5 OUT OUT+ MAX4362 PIN NAME µMAX T1IN T1IN SHDN 4 5 T2IN T2IN GND 7 10 T2OUT T1OUT — ...
Page 8
... Pin Descriptions (continued) FUNCTION Uncommitted Dual Amplifier for ADSL The MAX4362 is a dual amplifier with shutdown intend- ed for use as a differential IN/differential OUT driver with gain set with external resistors Uncommitted Quad Amplifier for ADSL The MAX4363 is a quad amplifier with shutdown intended for use as a differential IN/differential OUT driver/receiver combination with gain set with external resistors ...
Page 9
... MAX4361/MAX4362/MAX4363 outputs. The MAX4361/MAX4362 require a single 0.1µF bypass from V+ to ground located as close as possible to the IC leads. The MAX4363 features separate supply and ground pins for the receiver and driver amplifiers. Bypass the V+ (RX) supply to the GND (RX) pin with a 0.1µ ...
Page 10
... The 27.5dBm peak line power translates into a 28.4V peak-to-peak differential voltage on the 100Ω telephone line. The maximum low-distortion output swing available from the MAX4361/MAX4362/MAX4363 line driver supply is 3.8V and, taking into account the power lost due to the back-matching resistance, a step-up transformer with turns ratio of 3 ...
Page 11
ADSL Drivers/Receivers for Customer Premise 5V 5V 2.7kΩ 0.1µF 2.7kΩ 10kΩ 0.047µF 1kΩ 10kΩ 0.047µF ADSL CHIPSET ______________________________________________________________________________________ Typical Operating Circuit 0.1µF 1kΩ 1kΩ IN1+ OUT+ IN1- DRIVER IN2- OUT- IN2+ 1kΩ MAX4363 1kΩ 5V OUT+ IN1- IN1+ ...
Page 12
ADSL Drivers/Receivers for Customer Premise Equipment 12 ______________________________________________________________________________________ Package Information ...
Page 13
... ADSL Drivers/Receivers for Customer Premise Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 © ...