MAX349 Maxim, MAX349 Datasheet
MAX349
Available stocks
Related parts for MAX349
MAX349 Summary of contents
Page 1
... MICROWIRE™. Functioning as a shift register, it allows data (at DIN clocked in synchronously with the rising edge of clock (SCLK). The shift register’s output (DOUT) enables several MAX349s or MAX350s to be daisy chained. All digital inputs have 0.8V or 2.4V logic thresholds, ensuring both TTL and CMOS-logic compatibility when using ± ...
Page 2
... SSOP (derate 8.00mW/°C above +70°C) ..........640mW 18-Pin CERDIP (derate 10.53mW/°C above +70°C).....842mW Operating Temperature Ranges MAX349C_ _, MAX350C_ _ .................................0°C to +70°C MAX349E_ _, MAX350E_ _ ...............................-40°C to +85°C MAX349M_ _, MAX350M_ _ ...........................-55°C to +125°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10sec) .............................+300° ...
Page 3
... COM Off-Capacitance C Switch On-Capacitance Off-Isolation Channel-to-Channel Crosstalk POWER SUPPLY Power-Supply Range V+ Supply Current V- Supply Current _______________________________________________________________________________________ Serially Controlled, Low-Voltage unless otherwise noted. Typical values are MIN MAX CONDITIONS MAX349 V+ = 5.5V -5.5V, COM(ON COM NO ±4.5V MAX350 ...
Page 4
... Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the specified analog signal range. Note 3: Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at room temp. Note 4: Guaranteed by design. Note 5: Leakage testing at single supply is guaranteed by testing with dual supplies. ...
Page 5
... 5.5V 4.5V, COM NO(OFF 5.5V 0V, COM V = 4.5V NO MAX349 V+ = 5.5V 4.5V, COM MAX350 COM(OFF) MAX349 V+ = 5.5V 0V, COM V = 4.5V NO MAX350 MAX349 V+ = 5.5V COM(ON) COM NO ±4.5V MAX350 DIN SCLK 0. 0.8mA DOUT DOUT -1.6mA DOUT ...
Page 6
Serially Controlled, Low-Voltage, 8-Channel/Dual 4-Channel Multiplexers ELECTRICAL CHARACTERISTICS—Single +5V Supply (continued) (V+ = +4.5V to +5.5V 0V MIN PARAMETER SYMBOL SWITCH DYNAMIC CHARACTERISTICS Turn-On Time Turn-Off Time Break-Before-Make Delay Charge Injection (Note 4) Off-Isolation ...
Page 7
... Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the specified analog signal range. Note 3: Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at room temp. Note 4: Guaranteed by design. Note 5: Leakage testing at single supply is guaranteed by testing with dual supplies. ...
Page 8
... Typical values are at T MAX CONDITIONS , 3.0V 1.5V, COM 1mA NO MAX349 V+ = 3.6V 3V, COM MAX350 MAX349 V+ = 3.6V 0V, COM MAX350 MAX349 V+ = 3.6V COM NO MAX350 DIN SCLK , 0. 0.1mA DOUT DOUT I = -1.6mA DOUT DOUT ...
Page 9
Multiplexers ELECTRICAL CHARACTERISTICS—Single +3V Supply (continued) (V+ = +3.0V to +3.6V 0V MIN PARAMETER SYMBOL SWITCH DYNAMIC CHARACTERISTICS Turn-On Time (Note 4) Turn-Off Time (Note 4) Break-Before-Make Delay (Note 4) t Charge ...
Page 10
... Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the specified analog signal range. Note 3: Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at room temp. Note 4: Guaranteed by design. Note 5: Leakage testing at single supply is guaranteed by testing with dual supplies. ...
Page 11
Multiplexers __________________________________________Typical Operating Characteristics (V+ = +5V -5V, GND = 0V +25°C, unless otherwise noted.) A ON-RESISTANCE vs. V COM (DUAL SUPPLIES) 140 120 V± = ±2.5V 100 V± = ± V± ...
Page 12
Serially Controlled, Low-Voltage, 8-Channel/Dual 4-Channel Multiplexers (V+ = +5V -5V, GND = 0V +25°C, unless otherwise noted.) A DATA SETUP TIME vs. POSITIVE SUPPLY VOLTAGE 100 ...
Page 13
... Multiplexers PIN MAX349 MAX350 DIP/SO SSOP DIP/ — 6–13 6–9, 11–14 — — — 5 — — 6–9 — — 10–13 — — 10, 15, 16 — Note: NO and COM pins are identical and interchangeable. Either may be considered as an input or an output; signals pass equally well in either direction ...
Page 14
... MAX350s, “daisy-chain” the shift registers as shown in Figure 5. The CS pins of all devices are connected, 14 ______________________________________________________________________________________ and a stream of data is shifted through the MAX349s or MAX350s in series. When CS is brought high, all switches are updated simultaneously. Additional shift registers may be included anywhere in series with the MAX349/MAX350 data chain ...
Page 15
... Multiplexers Table 1. MAX349 Serial-Interface Switch Programming RESET ...
Page 16
... DOUT is sourced from V+. RESET must not be driven beyond V+ or GND. MAX349 MICROWIRE MAX350 PORT THE DOUT-MISO CONNECTION IS NOT REQUIRED FOR WRITING TO THE MAX349/MAX350, BUT MAY BE USED FOR DATA-ECHO PURPOSES. Figure 4. Connections for SPI and QSPI SCLK MAX349 MAX350 DIN DOUT ...
Page 17
... FOUR CLOCK PULSES Figure 7. Differential Multiplexer Input Control Power-Supply Considerations The MAX349/MAX350 construction is typical of most CMOS analog switches. It has three supply pins: V+, V- and GND. V+ and V- are used to drive the internal CMOS switches, and they set the limits of the analog voltage on any switch. Reverse ESD-protection diodes are internally connected between each analog signal pin and both V+ and V- ...
Page 18
... The V+ and V- supplies need not be symmetrical, but their sum cannot exceed the absolute maximum rating of 17V. Do not connect the MAX349/MAX350 V+ to +3V and connect the logic- level pins to TTL logic-level signals. This exceeds the absolute maximum ratings and can damage the part and/or external circuits ...
Page 19
... Plastic DIP 18 Wide SO COM 20 SSOP Dice* NO0 18 Plastic DIP 18 Wide SO NO1 20 SSOP 18 CERDIP** GND COMA NO0A NO1A TRANSISTOR COUNT: 500 SUBSTRATE CONNECTED TO V+. MAX349 V+ CS DIN SCLK RESET DOUT NO4 NO5 NO2 NO3 0.100" (2.54mm) MAX350 V+ CS SCLK DIN RESET DOUT ...
Page 20
... Multiplexers ________________________________________________________Package Information Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 20 © ...