MAX4509 Maxim, MAX4509 Datasheet
MAX4509
Available stocks
Related parts for MAX4509
MAX4509 Summary of contents
Page 1
... The MAX4508/MAX4509 are 8-to-1 and dual 4-to-1 fault- protected multiplexers that are pin compatible with the industry-standard DG508/DG509. The MAX4508/ MAX4509 operate with dual supplies of ±4.5V to ±20V or a single supply of +9V to +36V. These multiplexers fea- ture fault-protected inputs, rail-to-rail signal handling capability, and overvoltage clamping at 150mV beyond the rails. Both parts offer ± ...
Page 2
... PDIP (derate 10.53mW/°C above +70°C)..........842mW 16-Pin CERDIP (derate 10.00mW/°C above +70°C).....800mW Operating Temperature Ranges MAX4508C_ E/MAX4509C_E...............................0°C to +70°C MAX4508E_ E/MAX4509E_E ............................-40°C to +85°C MAX4508MJE/MAX4509MJE..........................-55°C to +125°C Storage Temperature Range .............................-65°C to +160°C Lead Temperature (soldering, 10s) .................................+300° ...
Page 3
Fault-Protected, High-Voltage Single 8-to-1/ Dual 4-to-1 Multiplexers with Output Clamps ELECTRICAL CHARACTERISTICS—Dual Supplies (continued) (V+ = +15V -15V +2.4V +25°C.) (Note 2) A PARAMETER SYMBOL FAULT PROTECTION Fault-Protected Analog Signal V ...
Page 4
... EN A MIN CONDITIONS R = 75Ω 15pF 1MHz, Figure 7 NO_ RMS f = 1MHz, Figure 8 MAX4508 f = 1MHz, Figure 8 MAX4509 MAX4508 f = 1MHz, Figure 8 MAX4509 All 5V NO_ All 5V NO_ All 5V NO_ ...
Page 5
... MIN CONDITIONS MAX4508 V = 10V, 1V; COM_ V = 1V, 10V NO_ MAX4509 MAX4508 V = 10V, 1V; COM_ V = 10V, 1V, or NO_ floating MAX4509 Applies with all power on NO_ Applies with all power off V = ±25V 12V NO_ V = ±25V NO_ COM_ V+ = 12V V = ±40V NO_ V = 25V 12V ...
Page 6
... ON ON(MAX) ON(MIN) Note 6: Leakage parameters are 100% tested at the maximum rated hot temperature and guaranteed by correlation at T Note 7: Off-Isolation = 20log10 (V COM_ Note 8: Between any two analog inputs. Note 9: Leakage testing for single-supply operation is guaranteed by testing with dual supplies. Note 10: Guaranteed by testing with dual supplies. ...
Page 7
Fault-Protected, High-Voltage Single 8-to-1/ Dual 4-to-1 Multiplexers with Output Clamps (V+ = +15V -15V +2.4V ON-RESISTANCE vs. V (DUAL SUPPLIES) COM 1000 900 V+ = +4.5V 800 V- = -4.5V 700 V+ = +10V ...
Page 8
Fault-Protected, High-Voltage Single 8-to-1/ Dual 4-to-1 Multiplexers with Output Clamps ( V+ = +15V -15V +2.4V POWER-SUPPLY CURRENT vs. TEMPERATURE (V 300 I+ 200 100 I GND 0 -100 I- -200 -300 -55 ...
Page 9
... NO3 limiting the output signal range to approximately 3V less than the appropriate polarity supply voltage. NO4 NO5 The MAX4508/MAX4509 differ considerably from tradi- tional fault-protected multiplexers, offering several NO6 advantages. First, they are constructed with two paral- NO7 lel FETs, allowing very low resistance when the switch NO8 is on ...
Page 10
... NO_ pin with V+ and V- supply voltages. When the signal on NO_ is between V+ and V-, the multiplexer behaves normally, with FETs N1 and P1 turning on and off in response to A_ signals (Figure 1). The parallel P2 P1 COM_ N1 MAX4508 MAX4509 N2 NO_ Input Voltage may range higher or lower than the sup NO_ COM_ Normal Operation ⎢ is ...
Page 11
... The MAX4508/MAX4509 operate with bipolar supplies between ±4.5V and ±20V. The V+ and V- supplies need not be symmetrical, but their sum cannot exceed the 44V absolute maximum rating. The MAX4508/MAX4509 operate from single supplies between +9V and +36V when V- is connected to GND Logic Level Thresholds Applications Information ...
Page 12
... EN EN NO2–NO8 A0 MAX4508 A1 A2 GND V- 50Ω -15V +15V NO1B NO1A–NO4A NO2B–NO4B, A0 COMA MAX4509 A1 COMB GND V- 50Ω -15V Figure 3. Enable Switching Time 12 ______________________________________________________________________________________ Test Circuits/Timing Diagrams NO1 +10V NO8 -10V LOGIC COM V INPUT OUT V 35pF ...
Page 13
Fault-Protected, High-Voltage Single 8-to-1/ Dual 4-to-1 Multiplexers with Output Clamps +15V +2.4V EN NO1–NO8 A0 MAX4508 GND V- 50Ω -15V Figure 4. MAX4508 Break-Before-Make Interval MAX4508 V ...
Page 14
... LOGIC "1" V ≥ +2.4V LOGIC "0" MAX4509 SWITCH NONE ≤ +0.8V, LOGIC "1" V ≥ +2.4V LOGIC "0" V ...
Page 15
... Narrow SO MAX4509CPE+ 0°C to +70°C 16 Plastic DIP MAX4509C/D 0°C to +70°C Dice* MAX4509ESE+ -40°C to +85°C 16 Narrow SO MAX4509EPE+ -40°C to +85°C 16 Plastic DIP MAX4509MJE -40°C to +85°C 16 CERDIP** *Contact factory for dice specifications. **Contact factory for availability. +Denotes a lead-free package. _______________________________________________________________________________________ EN ...
Page 16
... Fault-Protected, High-Voltage Single 8-to-1/ Dual 4-to-1 Multiplexers with Output Clamps (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages TOP VIEW D e FRONT VIEW 16 ______________________________________________________________________________________ INCHES DIM MIN A 0.053 A1 0 ...
Page 17
... Fault-Protected, High-Voltage Single 8-to-1/ Dual 4-to-1 Multiplexers with Output Clamps (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages.) ______________________________________________________________________________________ Package Information (continued) 17 ...
Page 18
... EC table changes and stylistic corrections Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 18 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © ...