CS61574A Cirrus Logic, Inc., CS61574A Datasheet - Page 26

no-image

CS61574A

Manufacturer Part Number
CS61574A
Description
T1/E1 LINE INTERFACE
Manufacturer
Cirrus Logic, Inc.
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
CS61574A-1212
Manufacturer:
CRYSTAL
Quantity:
20 000
Part Number:
CS61574A-IC1
Manufacturer:
CRYSTAL
Quantity:
402
Part Number:
CS61574A-IH
Manufacturer:
CRYSTAL
Quantity:
1 100
Part Number:
CS61574A-IL
Manufacturer:
CRYSTAL
Quantity:
11 698
Part Number:
CS61574A-IL1
Manufacturer:
CSI
Quantity:
5 530
Part Number:
CS61574A-IL1
Manufacturer:
CSI
Quantity:
6 100
Part Number:
CS61574A-IL1
Manufacturer:
CRYSTAL
Quantity:
862
Part Number:
CS61574A-IL1
Manufacturer:
CRYSTRL
Quantity:
20 000
Part Number:
CS61574A-IL1Z
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
Part Number:
CS61574A-IL1ZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
Part Number:
CS61574A-IP1
Manufacturer:
CRYSTAL
Quantity:
546
Part Number:
CS61574A-IP1
Manufacturer:
CRYSTAL
Quantity:
8 000
Part Number:
CS61574A-IP1
Manufacturer:
CS
Quantity:
20 000
TTIP, TRING - Transmit Tip, Transmit Ring, Pins 13 and 16.
Status
AIS - Alarm Indication Signal, Pin 11. (Extended Hardware Mode)
BPV- Bipolar Violation Strobe, Pin 6. (Extended Hardware Mode)
DPM - Driver Performance Monitor, Pin 11. (Hardware and Host Modes)
LOS - Loss of Signal, Pin 12.
MTIP, MRING - Monitor Tip, Monitor Ring, Pins 17 and 18. (Hardware and Host Modes)
Ordering Guide
26
CS61575-IP1
CS61575-IL1
CS61574A-IP1
CS61574A-IL1
The AMI signal is driven to the line through these pins. The transmitter output is designed to
drive a 75
AIS goes high when unframed all-ones condition (blue alarm) is detected, using the detection
criteria of less than three zeros out of 2048 bit periods.
BPV strobes high when a bipolar violation is detected in the received signal. B8ZS (or HDB3)
zero substitutions are not flagged as bipolar violations if the B8ZS (or HDB3) decoder has been
enabled.
DPM goes high if no activity is detected on MTIP and MRING.
LOS goes high when 175 consecutive zeros have been received. LOS returns low when the ones
density reaches 12.5% (based upon 175 bit periods starting with a one and containing less than
100 consectutive zeros) as prescribed in ANSI T1.231-1993. When in the loss of signal state
RPOS/RNEG or RDATA are forced low, and ACLKI (if present) is output on RCLK via the jitter
attenuator. If ACLKI is not present during LOS, RCLK is forced to the center frequency of the
crystal oscillator.
These pins are normally connected to TTIP and TRING and monitor the output of a line interface
IC. If the INT pin in the host mode is used, and the monitor is not used, writing "clear DPM" to
the serial interface will prevent an interrupt from the driver performance monitor.
Model
load between TTIP and TRING. A transformer is required as shown in Table A1.
Frequency
T1 & E1
T1 & E1
T1 & E1
T1 & E1
FIFO Depth (Bits)
192
192
32
32
Package
28-pin Plastic DIP
28-pin PLCC
28-pin Plastic DIP
28-pin PLCC
CS61574A CS61575
DS154F2

Related parts for CS61574A