MT9JSF12872PY-1G1 Micron Semiconductor Products, MT9JSF12872PY-1G1 Datasheet - Page 8

• Manufacturer Part Number: MT9JSF12872PY-1G1
• Description: 1gb, 2gb X72, Ecc, Sr 240-pin Ddr3 Sdram Rdimm
• Manufacturer: Micron Semiconductor Products

Electrical Specifications
Table 7:
Table 8:
Input Capacitance
Component AC Timing and Operating Conditions
PDF: 09005aef829eedac/Source: 09005aef829eede3
JTF9C128_256x72PY.fm - Rev. A 7/07 EN
V
Symbol
Symbol
IN
T
T
I
V
V
I
VREF
, V
A
I
C
VTT
OZ
TT
DD
I
2, 3
2, 3
I
OUT
1
Absolute Maximum Ratings
Operating Conditions
Parameter
V
Voltage on any pin relative to V
Input leakage current; Any input 0V ≤ V
V
under test = 0V)
Output leakage current; 0V ≤ V
and ODT are disabled
V
Parameter
Termination reference current from V
Termination reference voltage – command address bus
Module ambient operating temperature
DDR3 SDRAM component case operating
temperature
REF
REF
DD
Notes:
supply voltage relative to V
input 0V ≤ V
leakage current; V
4
Stresses greater than those listed in Table 7 may cause permanent damage to the
module. This is a stress rating only, and functional operation of the module at these or
any other conditions outside those indicated in the device data sheet is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect reli-
ability.
1. V
2. The T
3. For further information, refer to technical note
4. Refresh rate is required to double when 85°C < T
Micron encourages designers to simulate the performance of the module to achieve
optimum values. Simulations are significantly more accurate and realistic than a gross
estimation of module capacitance when inductance and delay parameters associated
with trace lengths are used in simulations.
Recommended AC operating conditions are given in the DDR3 component data sheets.
Component specifications are available on Micron’s Web site. Module speed grades
correlate with component speed grades, as shown in Table 9 on page 9.
address signals’ voltage margin and will reduce timing margins.
on Micron’s Web site.
IN
TT
≤ 0.95V (All other pins not
termination voltage in excess of stated limit will adversely affect the command and
A
REF
and T
= valid V
C
OUT
are simultaneous requirements.
SS
SS
1GB, 2GB (x72, ECC, SR) 240-Pin DDR3 SDRAM RDIMM
≤ V
REF
TT
DD
level
IN
Q; DQs
≤ V
DD
8
Commercial
Industrial
Commercial
Industrial
;
Address inputs
RAS#, CAS#, WE#,
S#, CKE, ODT, BA
CK, CK#
DM
DQ, DQS, DQS#
Micron Technology, Inc., reserves the right to change products or specifications without notice.
TN-00-08: Thermal
C
–0.483 × V
≤ 95°C.
–600
Min
–40
–40
0
0
Electrical Specifications
–TBD
DD
Min
–0.4
–0.4
–18
–5
–1
–1
©2007 Micron Technology, Inc. All rights reserved.
+0.517 × V
Applications, available
Max
+600
+70
+85
+85
+95
+1.975
+1.975
+TBD
Max
+150
+18
+1
+1
DD
Units
Units
mA
µA
µA
µA
°C
°C
°C
°C
V
V
V