D206EI MicroPower Direct, D206EI Datasheet - Page 2

• Manufacturer Part Number: D206EI
• Description: Low Cost, 2W SIP High Isolation Dc/dc Converters
• Manufacturer: MicroPower Direct

Model Selection Guide
Notes:
1. Output load regulation is specifi ed for a load change of 10% to
2. These units should not be operated with a load under 10% of
3. These converters will operate without external components.
4. Dual output units may be connected to provide a 10V, 18V, 24V
5. It is recommended that a fuse be used on the input of a power
Model
Number
D201EI
D202EI
D203EI
D204EI
D205EI
D206EI
D207EI
D208EI
D211EI
D212EI
D213EI
D214EI
D215EI
D216EI
D217EI
D218EI
D221EI
D222EI
D223EI
D224EI
D225EI
D226EI
D227EI
D228EI
100%.
full load. Operation at no-load may cause damage to the unit.
However, when measuring output ripple, it is recommended
that an external ceramic capacitor be placed from the +Vout
pin to the -Vout pin for single output units and from each out-
put to common for dual output units. An input capacitor will
enhance stability over temperature and input line variations.
Recommended capacitor values are given in the table below.
For applications requiring very low output noise levels, a simple
LC fi lter should be effective.
or 30 VDC output. To do this, connect the load across the posi-
tive (+Vout) and negative (-Vout) outputs and fl oat the output
common
supply for protection. See the Model Selection table above for
the correct rating.
Notes:
•
•
•
All dimensions are typical in inches (mm)
Tolerance x.xx =
Pin 1 is marked by a “dot” or indentation on the side of the unit
12 VDC
24 VDC
5 VDC
Pin Connections
Vin
Pin
Nominal
1
2
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
Voltage (VDC)
5
5
5
5
5
5
5
5
Single
Capacitor
-Vout
+Vin
-Vin
4.7 µF
2.2 µF
1.0 µF
Input
292 Page Street Ste D Stoughton, MA 02072
±
MicroPower Direct
0.01 (
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
Range
-Vout
Dual
+Vin
-Vin
12 VDC
15 VDC
5 VDC
9 VDC
±
Vout
0.25)
Input
Output Capacitor
Full-Load
10.0 µF
Pin
Single
4.7 µF
2.2 µF
1.0 µF
6
7
500
494
488
476
488
482
470
470
208
201
198
196
201
198
194
194
103
Current (mA)
99
98
97
99
98
96
96
www.micropowerdirect.com
No Pin
Single
+Vout
0.47 µF
4.7 µF
2.2 µF
1.0 µF
Dual
No-Load
Common
30
30
30
30
30
30
30
30
15
15
15
15
15
15
15
15
8
8
8
8
8
8
8
8
+Vout
Dual
Voltage
±12.0
±15.0
±12.0
±15.0
±12.0
±15.0
(VDC)
12.0
15.0
±5.0
±9.0
12.0
15.0
±5.0
±9.0
12.0
15.0
±5.0
±9.0
Derating Curve
5.0
9.0
5.0
9.0
5.0
9.0
(mA, Max)
•
±200.0
±111.0
±200.0
±111.0
±200.0
±111.0
Current
400.0
222.0
167.0
133.0
±83.0
±67.0
400.0
222.0
167.0
133.0
±83.0
±67.0
400.0
222.0
167.0
133.0
±83.0
±67.0
Output
TEL: [phone]
Mechanical Dimensions
(mA, Min)
Current
±20.0
±12.0
±20.0
±12.0
±20.0
±12.0
40.0
23.0
17.0
14.0
±9.0
±7.0
40.0
23.0
17.0
14.0
±9.0
±7.0
40.0
23.0
17.0
14.0
±9.0
±7.0
•
Regulation
(%, Max)
FAX: [phone]
Load
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
Effi ciency
(%, Typ)
80
81
82
84
82
83
85
85
80
83
84
85
83
84
86
86
81
84
85
86
84
85
87
87
•
E-Mail: [e-mail]
Fuse Rating
Slow-Blow
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
(mA)
500
500
500
500
500
500
500
500
200
200
200
200
200
200
200
200