LM2574-12 Motorola Inc, LM2574-12 Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
LM2574-12
Manufacturer Part Number
LM2574-12
Description
EASY SWITCHERE 0.5 A STEP-DOWN VOLTAGE REGULATOR
Manufacturer
Motorola Inc
Datasheet
1.LM2574-12.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM2574-12
Manufacturer:
LT
Quantity:
3 442
Company:
Part Number:
LM2574-12BN
Manufacturer:
TI
Quantity:
2 000
Company:
Part Number:
LM2574-12BWM
Manufacturer:
MOT
Quantity:
15
Company:
Part Number:
LM2574-12YN
Manufacturer:
MicrelInc
Quantity:
2 000
Procedure (Fixed Output Voltage Version) (continued) In order to simplify the switching regulator design, a step–by–step
design procedure and example is provided.
Procedure (Adjustable Output Version: LM2574–ADJ)
MOTOROLA ANALOG IC DEVICE DATA
5. Output Capacitor Selection (C out )
Given Parameters:
1. Programming Output Voltage
2. Input Capacitor Selection (C in )
3. Catch Diode Selection (D1)
A. Since the LM2574 is a forward–mode switching regulator
B. Due to the fact that the higher voltage electrolytic capacitors
V out = Regulated Output Voltage
V in(max) = Maximum DC Input Voltage
I Load(max) = Maximum Load Current
To select the right programming resistor R1 and R2 value (see
Figure 2) use the following formula:
Resistor R1 can be between 1.0 k and 5.0 k . (For best
temperature coefficient and stability with time, use 1% metal
film resistors).
To prevent large voltage transients from appearing at the input
and for stable operation of the converter, an aluminium or
tantalum electrolytic bypass capacitor is needed between the
input pin +V in and ground pin Gnd. This capacitor should be
located close to the IC using short leads. This capacitor should
have a low ESR (Equivalent Series Resistance) value.
For additional information see input capacitor section in the
“EXTERNAL COMPONENTS” section of this data sheet.
A. Since the diode maximum peak current exceeds the
B. The reverse voltage rating of the diode should be at least
with voltage mode control, its open loop 2–pole–1–zero
frequency characteristic has the dominant pole–pair
determined by the output capacitor and inductor values. For
stable operation and an acceptable ripple voltage,
(approximately 1% of the output voltage) a value between
100 F and 470 F is recommended.
generally have lower ESR (Equivalent Series Resistance)
numbers, the output capacitor’s voltage rating should be at
least 1.5 times greater than the output voltage. For a 5.0 V
regulator, a rating at least 8.0 V is appropriate, and a 10 V
or 16 V rating is recommended.
regulator maximum load current the catch diode current
rating must be at least 1.2 times greater than the maximum
load current. For a robust design, the diode should have a
current rating equal to the maximum current limit of the
LM2574 to be able to withstand a continuous output short.
1.25 times the maximum input voltage.
V out
+
V
R2
ref
+
1.0
R1
Procedure
Procedure
)
V out
V
R2
R1
ref
*
where V ref = 1.23 V
1.0
LM2574
5. Output Capacitor Selection (C out )
Given Parameters:
1. Programming Output Voltage ( selecting R1 and R2)
2. Input Capacitor Selection (C in )
3. Catch Diode Selection (D1)
A. C out = 100 F to 470 F standard aluminium electrolytic.
B. Capacitor voltage rating = 20 V.
V out = 24 V
V in(max) = 40 V
I Load(max) = 0.4 A
Select R1 and R2 :
R2 = 18.51 k , choose a 18.7 k metal film resistor.
A 22 F aluminium electrolytic capacitor located near the input
and ground pin provides sufficient bypassing.
A. For this example, a 1.0 A current rating is adequate.
B. Use a 50 V MBR150 Schottky diode or any suggested fast
R2
V out = 1.23
recovery diodes in Table 1.
+
R1
V out
V
ref
1.0
*
)
1.0
R2
R1
Example
Example
+
Select R1 = 1.0 k
1.0 k
1.23 V
10 V
*
1.0
11