CLAA154WB04 CHUNGHWA PICTURE TUBES, CLAA154WB04 Datasheet - Page 20

• Manufacturer Part Number: CLAA154WB04
• Description: Display Module
• Manufacturer: CHUNGHWA PICTURE TUBES

CPT
11. HANDLING PRECAUTIONS FOR TFT-LCD MODULE
Please pay attention to the followings in handling- TFT-LCD products;
11.1 ASSEMBLY PRECAUTION
11.2 OPERATING PRECAUTIONS
11.3 PRECAUTIONS WITH ELECTROSTATICS
11.4 STORAGE PRECAUTIONS
11.5 SAFETY PRECAUTIONS
CPT Confidential
(1) Please use the mounting hole on the module side in installing and do not beading or wrenching
(2) Please design display housing in accordance with the following guidelines.
(3) Please do not push or scratch LCD panel surface with any-thing hard. And do not soil LCD panel surface by
(4) Please do not press any parts on the rear side such as source TCP, gate TCP, control circuit board and FPCs during
(5) Please wipe out LCD panel surface with absorbent cotton or soft clothe in case of it being soiled.
(6) Please wipe out drops of adhesives like saliva and water on LCD panel surface immediately. They might damage to
(7) Please do not take a LCD module to pieces and reconstruct it. Resolving and reconstructing modules may cause
(8) Please do not touch metal frames with bare hands and soiled gloves. A color change of the metal frames can happen
(9) Please pay attention to handling lead wire of backlight so that it is not tugged in connecting with inverter.
(1) Please be sure to turn off the power supply before connecting and disconnecting signal input cable.
(2) Please do not change variable resistance settings in LCD module. They are adjusted to the most suitable value. If
(3) Please consider that LCD backlight takes longer time to become stable of radiation characteristics in low temperature
(4) A condensation might happen on the surface and inside of LCD module in case of sudden change of ambient
(5) Please pay attention to displaying the same pattern for very long time. Image might stick on LCD. If then, time
(6) Please obey the same caution descriptions as ones that need to pay attention to ordinary electronic parts.
(1) This LCD module use CMOS-IC on circuit board and TFT-LCD panel, and so it is easy to be affected by
(2) Please remove protection film very slowly on the surface of LCD module to prevent from electrostatics occurrence.
(1) When you store LCDs for a long time, it is recommended to keep the temperature between 0℃ ~40℃ without the
(2) Please do not leave the LCDs in the environment of high humidity and high temperature such as 60℃ 90%RH.
(3) Please do not leave the LCDs in the environment of low temperature; below -20℃.
(1) When you waste LCDs, it is recommended to crush damaged or unnecessary LCDs into pieces and wash them off
(2) If any liquid leaks out of a damaged-glass cell and comes in contact with the hands, wash off throughly with soap
LCD in assembling. And please do not drop, bend or twist LCD module in handling.
touching with bare hands. (Polarizer film, surface of LCD panel is easy to be flawed.)
handling LCD module. If pressing rear part is unavoidable, handle the LCD module with care not to damage them.
cause panel surface variation and color change.
them not to work well.
during a long preservation of soiled LCD modules.
they are changed, it might happen LCD does not satisfy the characteristics specification.
than in room temperature.
temperature.
going on can make LCD work well.
electrostatics. Please be careful with electrostatics by the way of your body connecting to the ground and so on.
exposure of sunlight and to keep the humidity less than 90%RH.
with solvents such as acetone and ethanol, which should later be burned.
and water.
• Housing case must be destined carefully so as not to put stresses on LCD all sides and not to wrench module.
• Keep sufficient clearance between LCD module back surface and housing when the LCD module is mounted.
• When some parts, such as, FPC cable and ferrite plate, are installed underneath the LCD module, still sufficient
• Design the inverter location and connector position carefully so as not to give stress to lamp cable, or not to
• Keep sufficient clearance between LCD module and the others parts, such as inverter and speaker so as not to
The stresses may cause non-uniformity even if there is no non-uniformity statically.
Approximately 1.0 mm of the clearance in the design is recommended taking into account the tolerance of
LCD module thickness and mounting structure height on the housing.
clearance is required, such as 0.5mm. This clearance is, especially, to be reconsidered when the additional
parts are implemented for EMI countermeasure.
interface the LCD module by the lamp cable.
interface the LCD module. Approximately 1.0mm of the clearance in the design is recommended.
20/21
www.DataSheet.net/
CHUNGHWA PICTURES TUBES, LTD.,
CLAA154WB04-STUDIO-
20061205
www.yslcd.com.tw
Datasheet pdf - http://www.DataSheet4U.co.kr/