DCR1594SW Dynex Semiconductor, DCR1594SW Datasheet
DCR1594SW
Related parts for DCR1594SW
DCR1594SW Summary of contents
Page 1
... Lower voltage grades available. ORDERING INFORMATION When ordering, select the required part number shown in the Voltage Ratings selection table. For example: DCR1594SW25 Note: Please use the complete part number when ordering and quote this number in any future correspondance relating to your order. www.dynexsemi.com ...
Page 2
... DCR1594SW CURRENT RATINGS T = 60˚C unless stated otherwise. case Symbol Parameter Double Side Cooled Mean on-state current I T(AV) RMS value I T(RMS) Continuous (direct) on-state current I T Single Side Cooled Mean on-state current I T(AV) I RMS value T(RMS) I Continuous (direct) on-state current 80˚C unless stated otherwise. ...
Page 3
... T = 125˚C case Test Conditions Double side cooled DC Single side cooled Anode DC Cathode DC Clamping force 70.0kN Double side (with mounting compound) Single side On-state (conducting) Reverse (blocking) DCR1594SW Max. Units Min ...
Page 4
... DCR1594SW SURGE RATINGS Symbol Parameter I /I Peak reverse and off-state current RRM RRM dV/dt Max. linear rate of rise of off-state voltage dI/dt Rate of rise of on-state current V Threshold voltage T(TO) r On-state slope resistance T t Delay time gd t Turn-off time q I Latching current L I Holding current H 4/10 Test Conditions ...
Page 5
... See table fig. 8 and 9 4000 T = 125˚C j 3500 3000 2500 2000 1500 1000 500 0 0.8 1.6 1.8 2.0 - (V) T Fig.3 Maximum (limit) on-state characteristics Where A = 1.152158 B = – 0.08401428 C = 3.351054x10 D = 0.01199439 these values are valid for T DCR1594SW Max 400 o C 0. 150 - 10 0.9 1.0 1.1 1.2 1.3 Instantaneous on-state voltage (V) T – ...
Page 6
... DCR1594SW 6000 5000 4000 3000 2000 1000 0 0 500 1000 1500 2000 Mean on-state current, I Fig.4 Sine wave power dissipation 6000 5000 4000 3000 2000 1000 0 0 1000 2000 3000 Mean on-state current, I Fig.6 Square wave power dissipation 6/10 2000 1800 1600 ...
Page 7
... Watts GM 400 150 125 100 25˚C j 0.3 0.4 0.5 Gate trigger current (A) GT Fig.8 Gate characteristics Gate trigger current (A) GT Fig.9 Gate characteristics DCR1594SW Upper limit Lower limit T = -40˚C j Preferred gate drive area 0.6 0.7 0.8 0 7/10 ...
Page 8
... DCR1594SW 10000 Max Min 1000 dI/dt 100 1.0 10 Rate of decay of on-state current dI/dt - (A/µs) Fig.10 Stored charge 0.1 0.01 0.001 Conduction Effective thermal resistance 0.0001 d.c. half wave 3 phase 120˚ 6 phase 60˚ 0.00001 0.001 0.01 0.1 Time - (s) Fig.12 Maximum (limit) transient thermal impedance - junction to case (˚C/W) 8/10 100 Conditions: ...
Page 9
... DO NOT SCALE. 2 holes Ø3.6x2.0 deep (in both electrodes) Cathode tab Gate www.dynexsemi.com Cathode Ø120 max Ø84.6 nom Ø84.6 nom Ø120 max Nominal weight: 2600g Clamping force: 70kN ±10% Lead length: 420mm Lead terminal connector: M4 ring Package outline type code: W DCR1594SW Anode 9/10 ...
Page 10
... DCR1594SW POWER ASSEMBLY CAPABILITY The Power Assembly group was set up to provide a support service for those customers requiring more than the basic semiconductor, and has developed a flexible range of heatsink and clamping systems in line with advances in device voltages and current capability of our semiconductors. ...