sl6610 Zarlink Semiconductor, sl6610 Datasheet
sl6610
Available stocks
Related parts for sl6610
sl6610 Summary of contents
Page 1
This product is obsolete. This information is available for your convenience only. For more information on Zarlink’s obsolete products and replacement product lists, please visit http://products.zarlink.com/obsolete_products/ ...
Page 2
... TPY GTHADJ TCADJ BEC BATTFL TPLIMY VCC2 DATAOP ABSOLUTE MAXIMUM RATINGS Supply voltage Storage temperature Operating temperature ORDERING INFORMATION SL6610 / KG / NPDS SL6610 / KG / NPDE Fig.2 Block diagram of SL6610 SL6610 Advance Information DS4003 - 2.2 September 1995 1 28 IAGCOUT 2 27 IRFAMP 3 26 MIXA 4 25 GND ...
Page 3
... SL6610 ELECTRICAL CHARACTERISTICS These characteristics are guaranteed over the following conditions unless otherwise stated: Tamb = 25°C, VCC1 = 1.3V, VCC2 = 2.7V Characteristics VCC1 - Supply voltage VCC2 - Supply voltage 21,27,28 ICC1 - Supply current 11,13,14 ICC2 - Supply current 21,27,28 Power down ICC1 11,13,14 Power down ICC2 1 volt regulator Band gap voltage reference ...
Page 4
... See Figs.8a, 8b See Fig.9 V Equal to Pin 21 (VCC1) 85 µA Units Comments 1200 bps f = 4kHz dBm LO = -18dBm 1200 bps f = 4kHz -18dBm dB 1200 bps f = 4kHz LO = -18dBm Channel spacing 25kHz 1200 bps f = 4kHz kHz LO = -18dBm 1200 bps f = 4kHz kHz LO = -18dBm SL6610 3 ...
Page 5
... SL6610 RECEIVER CHARACTERISTICS (Demonstration board) Measurement conditions unless stated V Carrier frequency 282MHz, BER 1 in 30, Tamb = 25°C (TPx/TPy typically:- 160mV ± 10% for - 73dBm RF input to the LNA) PP Characteristics Sensitivity Intermodulation (IP3) Intermodulation (IP2) Adjacent channel Centre frequency acceptance Deviation acceptance RECEIVER CHARACTERISTICS Measurement conditions unless stated V Carrier frequency 470MHz, BER 1 in 30, Tamb = 25° ...
Page 6
... Pin Typ Max Min 1 72.5 66 +/-1.8 +/-2.3 +/-2.2 -55 -59 -44 -48 -52 SL6610 Units Comments 1200 bps f = 4kHz -15dBm 1200 bps f = 4kHz -15dBm 1200 bps f = 4kHz -15dBm 1200 bps f = 4kHz -15dBm Channel spacing 25kHz kHz 1200 bps f = 4kHz kHz LO = -15dBm ...
Page 7
... SL6610 OPERATION OF SL6610 The SL6610 is a Direct Converson Receiver designed for use up to 470MHz available pin SSOP package and it integrates all the facilities required for the conversion FSK signal to a base-band data signal. Low Noise Amplifier To achieve optimum performance it is necessary to incorporate a Low Noise RF Amplifier at the front end of the receiver ...
Page 8
... Fig.3 Application circuit board SL6610 7 ...
Page 9
... SL6610 COMPONENTS LIST FOR APPLICATION BOARD (LO Circuit in Fig.3) Resistors R1 open circuit R2 not used R3 100 R4 100k 100 R8 open circuit R9 220k R10 1M R11 100k (6) R12 not used (1) R13 1k5 R14 4k7 R15 4k7 R16 33k R17 not used (3) R18 0R R19 10k ...
Page 10
... Applications Circuit with no Audio AGC connected. i.e. R17 and D1 omitted. 6. Suggested diode for use with the Audio AGC circuit (D1 is not included on the general demonstration circuit). 7. The value of R11 is dependent on the data output load. R11 should allow sufficient current to drive the data output load. SL6610 (6) 9 ...
Page 11
... SL6610 RF Amplifier Components Values Resistors R14, R15 4k7 R13 see note 1 R22 47k Notes: (1) The value of R13 is determined by the set up procedure (See "Set up for optimum performance"). (2) C20 and C21 are purely for deomonstration purposes. Pin 24 and Pin 26 may be DC coupled provided that no DC voltage is applied to the mixer inputs ...
Page 12
... Fig.6 AGC Schematic Fig.7 Audio AGC current vs. IP power at 25°C SL6610 11 ...
Page 13
... SL6610 S11 MAG FREQ 0.969 50.000 0.958 100.000 0.942 150.000 0.917 200.000 0.893 250.000 0.858 300.000 350.000 0.832 0.806 400.000 0.781 450.000 500.000 0.755 0.743 550.000 0.725 600.000 0.703 650.000 0.680 700.000 0.666 750.000 0.653 800.000 0.636 850.000 0.615 900.000 0.604 950 ...
Page 14
... Conditions:- 282MHz demonstration board i.e. 20dB LNA, 2dB noise figure, carrier frequency 282MHz, 1200bps baud rate, 4kHz deviation frequency, BER 1 in 30. Fig.10a AC parameters vs. supply and temperature SL6610 Vcc1 = 1.0V, Vcc2 = 1.8V Vcc1 = 1.3V, Vcc2 = 2.7V Vcc1 = 3.0V, Vcc2 = 4.0V 13 ...
Page 15
... SL6610 Conditions:- 282MHz demonstration board i.e. 20dB LNA, 2dB noise figure, carrier frequency 282MHz, 1200bps baud rate, 4kHz deviation frequency, BER 1 in 30. 14 Fig.10b AC parameters vs. supply and temperature Vcc1 = 1.0V, Vcc2 = 1.8V Vcc1 = 1.3V, Vcc2 = 2.7V Vcc1 = 3.0V, Vcc2 = 4.0V ...
Page 16
... AGC inactive). ICC2 measured with BATT FLAG and DATA O/P HIGH 282MHz. Note 1- IP3 is level above wanted needed to reduce receiver B.E.R. Fig.11 DC parameters vs. supply and temperature (IP3 vs audio AGC both on and off) SL6610 Vcc1 = 0.98V, Vcc2 = 1.78V Vcc1 = 1.3V, Vcc2 = 2.7V Vcc1 = 3.0V, Vcc2 = 4.0V 15 ...
Page 17
... SL6610 16 Fig.12 Sensitivity, IP3 vs Receiver Gain Fig.13 Sensitivity, adjacent Channel vs Receiver Gain ...
Page 18
... Fig.15 Sensitivity, Adjacent Channel vs LO level Sensitivity IP3 LO Drive Level (dBm) Fig.14 Sensitivity, IP3 vs LO level LO Drive Level (dBm) SL6610 73.5 Sensitivity 73 ACR 72 ...
Page 19
... SL6610 PACKAGE DETAILS Dimensions are shown thus: mm (in) HEADQUARTERS OPERATIONS MITEL SEMICONDUCTOR Cheney Manor, Swindon, Wiltshire SN2 2QW, United Kingdom. Tel: (01793) 518000 Fax: (01793) 518411 MITEL SEMICONDUCTOR 1500 Green Hills Road, Scotts Valley, California 95066-4922 United States of America. Tel (408) 438 2900 ...
Page 20
... For more information about all Zarlink products Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use ...