adt7410z Analog Devices, Inc., adt7410z Datasheet
adt7410z
Related parts for adt7410z
adt7410z Summary of contents
Page 1
... The INT and CT pins can operate in either comparator or interrupt mode. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 Fax: 781.461.3113 ©2008 Analog Devices, Inc. All rights reserved. ADT7410 CRIT ...
Page 2
ADT7410 PRODUCT HIGHLIGHTS • An on-chip temperature sensor allows an accurate measurement of the ambient temperature. The measurable temperature range is −55°C to +150°C. • Supply voltage is 2 5.5 V. • Available in an 8-lead narrow SOIC ...
Page 3
Preliminary Technical Data TABLE OF CONTENTS Features ............................................................................................... 1 Applications ....................................................................................... 1 Functional Block Diagram ............................................................... 1 General Description .......................................................................... 1 Product Highlights ............................................................................ 2 Revision History ................................................................................ 3 Specifications ..................................................................................... Timing Specifications ............................................................ 5 Timing ...
Page 4
ADT7410 SPECIFICATIONS T = −55°C to +150° 2 5.5 V, unless otherwise noted Table 1. Parameter Min TEMPERATURE SENSOR AND ADC Accuracy ADC Resolution Temperature Resolution 13 Bits 16 Bits Temperature Conversion Time Fast ...
Page 5
Preliminary Technical Data TIMING SPECIFICATIONS T = −55°C to +150° 2 5.5 V, unless otherwise noted. All input signals are specified with (10 and timed ...
Page 6
ADT7410 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter V to GND DD SDO Input Voltage to GND SDO Output Voltage to GND SCL Input Voltage to GND CT and INT Output Voltage to GND Operating Temperature Range Storage Temperature Range Maximum ...
Page 7
Preliminary Technical Data PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Table 4. Pin Function Descriptions Pin No. Mnemonic Description 1 SCL Serial Clock Input. This is the clock input for the serial port. The serial clock is used to clock in and ...
Page 8
ADT7410 TYPICAL PERFORMANCE CHARACTERISTICS Figure 6. Temperature Accuracy at 3.3 V and 5 V Figure 7. Operating Supply Current vs. Temperature Figure 8. Average Operating Supply Current vs. Supply Voltage at 30°C Preliminary Technical Data Figure 9. Shutdown Current vs. ...
Page 9
Preliminary Technical Data THEORY OF OPERATION CIRCUIT INFORMATION The ADT7410 is a 16-bit digital temperature sensor with the 16 bit acting as the sign bit. An on-board temperature sensor generates a voltage precisely proportional to absolute temperature, which is compared ...
Page 10
ADT7410 via the configuration register while the INT and CT pins are also programmable for interrupt mode via the configuration register. ONE-SHOT MODE Setting Bit and Bit the configuration register enables the one-shot ...
Page 11
Preliminary Technical Data TEMPERATURE 149°C 148°C 147°C 146°C 145°C 144°C 143°C 142°C 141°C 140°C CT PIN POLARITY = ACTIVE LOW CT PIN POLARITY = ACTIVE HIGH WRITE TO D5 AND D6 OF CONFIGURATION *THERE IS A 240ms DELAY BETWEEN WRITING ...
Page 12
ADT7410 SHUTDOWN The ADT7410 can be placed in shutdown mode via the configuration register, in which case the entire IC is shut down and no further conversions are initiated until the ADT7410 is taken out of shutdown mode. The ADT7410 ...
Page 13
Preliminary Technical Data REGISTERS The ADT7410 contains thirteen registers: • Nine temperature registers • One status register • One ID register • One configuration register • One address pointer register All registers are 8 bits wide. The temperature value register, ...
Page 14
ADT7410 STATUS REGISTER This 8-bit read-only register reflects the status of the over temperature and under temperature interrupts that can cause the CT and INT pins to go active. It also reflects the status of a temperature conversion operation. The ...
Page 15
Preliminary Technical Data T SETPOINT REGISTERS HIGH The T MSB and T LSB registers store the over temperature limit value. An over temperature event occurs when the temperature HIGH HIGH value stored in the temperature value register exceeds the value ...
Page 16
ADT7410 T SETPOINT REGISTER HYST This 8-bit read/write register stores the temperature hysteresis value for the T hysteresis value is stored in straight binary format using the four LSBs. Increments are possible in steps of 1°C from 0°C to +15°C. ...
Page 17
Preliminary Technical Data SERIAL INTERFACE Control of the ADT7410 is carried out via the I compatible serial interface. The ADT7410 is connected to this bus as a slave and is under the control of a master device. 2 Figure 14 ...
Page 18
ADT7410 WRITING DATA Depending on the register being written to, there are two different write transactions for the ADT7410. Writing to the Address Pointer Register for a Subsequent Read To read data from a particular register, the address pointer register ...
Page 19
Preliminary Technical Data 1 SCL SDA START BY MASTER FRAME 1 SERIAL BUS ADDRESS BYTE 1 SCL (CONTINUED) SDA (CONTINUED) D15 D14 D13 Figure 17. Writing to the Address Pointer Register Followed by Two Bytes ...
Page 20
ADT7410 1 SCL SDA START BY MASTER SERIAL BUS ADDRESS BYTE D15 D14 R/W ACK. BY ADT7410 FRAME 1 1 SCL (CONTINUED) SDA (CONTINUED LSB DATA BYTE FROM ...
Page 21
Preliminary Technical Data INT & CT OUTPUTS The INT and CT pins are open drain and require a pull-up resistor to VCC. INT OVERTEMPERATURE MODES The ADT7410 INT and CT pins have two temperature interrupt modes, comparator mode and interrupt ...
Page 22
ADT7410 (COMPARATOR MODE) POLARITY = ACTIVE LOW (INTERRUPT MODE) POLARITY = ACTIVE LOW (COMPARATOR MODE) POLARITY = ACTIVE HIGH (INTERRUPT MODE) POLARITY = ACTIVE HIGH Figure 21. INT Output Temperature Response Diagram for T TEMPERATURE -13°C -14°C -15°C -16°C -17°C ...
Page 23
Preliminary Technical Data APPLICATION INFORMATION THERMAL RESPONSE TIME The time required for a temperature sensor to settle to a specified accuracy is a function of the thermal mass of the sensor and the thermal conductivity between the sensor and the ...
Page 24
... ADT7410 OUTLINE DIMENSIONS ORDERING GUIDE Model Temperature Range 2 ADT7410Z –55°C to +150°C 1 Temperature accuracy is over the 0°C to +70°C temperature range RoHS Compliant Part. 5.00 (0.1968) 4.80 (0.1890 6.20 (0.2440) 4.00 (0.1574) 5.80 (0.2284) 3.80 (0.1497 1.27 (0.0500) BSC 1.75 (0.0688) 1.35 (0.0532) 0.25 (0.0098) 0.10 (0.0040) 0.51 (0.0201) COPLANARITY 0 ...
Page 25
Preliminary Technical Data NOTES Rev. PrE | Page ADT7410 ...
Page 26
ADT7410 NOTES Preliminary Technical Data Rev. PrE | Page ...
Page 27
... C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I 2 Rights to use these components system, provided that the system conforms to the I ©2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. PR06560-0-9/08(PrE Standard Specification as defined by Philips ...