nx3l1t53 NXP Semiconductors, nx3l1t53 Datasheet

no-image

nx3l1t53

Manufacturer Part Number
nx3l1t53
Description
Low-ohmic Single-pole Double-throw Analog Switch
Manufacturer
NXP Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
nx3l1t53GD
Manufacturer:
NXP
Quantity:
2 825
Part Number:
nx3l1t53GM
Manufacturer:
NXP
Quantity:
4 247
Part Number:
nx3l1t53GM
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
nx3l1t53GT
Manufacturer:
NXP
Quantity:
4 945
1. General description
2. Features
The NX3L1T53 provides one low-ohmic single-pole double-throw analog switch, suitable
for use as an analog or digital multiplexer/demultiplexer. It has a digital select input (S),
two independent inputs/outputs (Y0, Y1), a common input/output (Z) and an active LOW
enable input (E). When pin E is HIGH, the switch is turned off. Schmitt-trigger action at the
select input (S) and enable input (E) makes the circuit tolerant to slower input rise and fall
times across the entire V
A low input voltage threshold allows pins S and E to be driven by lower level logic signals
without a significant increase in supply current I
NX3L1T53 to switch 4.3 V signals with a 1.8 V digital controller, eliminating the need for
logic level translation.
The NX3L1T53 allows signals with amplitude up to V
Y1; or from Y0 or Y1 to Z. It’s low ON resistance (0.5 ) and flatness (0.13 ) ensures
minimal attenuation and distortion of transmitted signals.
I
I
I
I
I
I
I
I
I
I
I
I
NX3L1T53
Low-ohmic single-pole double-throw analog switch
Rev. 02 — 14 April 2009
Wide supply voltage range from 1.4 V to 4.3 V
Very low ON resistance (peak):
Break-before-make switching
High noise immunity
ESD protection:
CMOS low-power consumption
Latch-up performance exceeds 100 mA per JESD 78 Class II Level A
1.8 V control logic at V
Control input accepts voltages above supply voltage
Very low supply current, even when input is below V
High current handling capability (350 mA continuous current under 3.3 V supply)
Specified from 40 C to +85 C and from 40 C to +125 C
N
N
N
N
N
N
N
N
1.6
1.0
0.55
0.50
0.50
HBM JESD22-A114E Class 3A exceeds 7500 V
MM JESD22-A115-A exceeds 200 V
CDM AEC-Q100-011 revision B exceeds 1000 V
(typical) at V
(typical) at V
(typical) at V
(typical) at V
(typical) at V
CC
CC
CC
CC
CC
CC
CC
range from 1.4 V to 4.3 V.
= 1.4 V
= 1.65 V
= 3.6 V
= 2.3 V
= 2.7 V
= 4.3 V
CC
. This makes it possible for the
CC
CC
to be transmitted from Z to Y0 or
Product data sheet

Related parts for nx3l1t53

nx3l1t53 Summary of contents

Page 1

... V A low input voltage threshold allows pins S and driven by lower level logic signals without a significant increase in supply current I NX3L1T53 to switch 4.3 V signals with a 1.8 V digital controller, eliminating the need for logic level translation. The NX3L1T53 allows signals with amplitude ...

Page 2

... C to +125 C 5. Marking [1] Table 2. Marking codes Type number NX3L1T53GT NX3L1T53GD NX3L1T53GM [1] The pin 1 indicator is located on the lower left corner of the device, below the marking code. NX3L1T53_2 Product data sheet Low-ohmic single-pole double-throw analog switch Description XSON8 plastic extremely thin small outline package; no leads; ...

Page 3

... E 2 001aad386 001aaj537 Fig 4. Rev. 02 — 14 April 2009 NX3L1T53 001aad387 NX3L1T53 GND 3 GND 4 Transparent top view Pin configuration SOT996-2 (XSON8U 001aaj955 © NXP B.V. 2009. All rights reserved ...

Page 4

... LOW) 5 ground ( ground ( select input 2 independent input or output 1 independent input or output 8 supply voltage Rev. 02 — 14 April 2009 NX3L1T53 Z E GND Channel switch off © NXP B.V. 2009. All rights reserved ...

Page 5

... CC source or sink current V > 0 < 0 pulsed duration, < duty cycle; peak current +125 C amb tot Conditions select input S and enable input Rev. 02 — 14 April 2009 NX3L1T53 Min Max 0.5 +4.6 [1] 0.5 +4.6 [2] 0 +150 [3] - 250 derates linearly with 7.8 mW/K. ...

Page 6

... GND Figure GND Rev. 02 — 14 April 2009 NX3L1T53 +125 C amb amb Typ Max Min ( 1 ...

Page 7

... open circuit. O Conditions V = GND 100 mA; SW see Figure Rev. 02 — 14 April 2009 NX3L1T53 switch 001aad390 switch ...

Page 8

... amb switch GND Rev. 02 — 14 April 2009 NX3L1T53 Figure + +125 C Unit [1] Min Typ Max Min - 0.04 0 0.04 0 0.02 0. 0.02 0.075 - - 0.02 0.075 - - 1.0 3 0.5 1 ...

Page 9

... 0.8 0.6 0.4 0 (V) I (1) T (2) T (3) T (4) T Fig 11. ON resistance as a function of input voltage; Rev. 02 — 14 April 2009 NX3L1T53 001aag564 (V) I (1) (2) (3) ( 125 C. amb = 85 C. amb = 25 C. amb = 40 C. amb © NXP B.V. 2009. All rights reserved. ...

Page 10

... Fig 13. ON resistance as a function of input voltage; 001aag569 1 0.8 0.6 (1) (2) (3) (4) 0.4 0 (V) I (1) T (2) T (3) T (4) T Fig 15. ON resistance as a function of input voltage; Rev. 02 — 14 April 2009 NX3L1T53 125 C. amb = 85 C. amb = 25 C. amb = 40 C. amb (1) (2) (3) ( ...

Page 11

... Figure and V = 1.5 V, 1.8 V, 2.5 V, 3.3 V and 4.3 V respectively. amb CC Rev. 02 — 14 April 2009 NX3L1T53 +125 C [1] Typ Max Min Max ( 120 ...

Page 12

... GND t dis GND Table 10. are typical output voltage levels that occur with the output load. Input V M 0.5V CC Rev. 02 — 14 April 2009 NX3L1T53 dis 001aah457 Output V X 0.9V OH © NXP B.V. 2009. All rights reserved ...

Page 13

... GND V I 0. GND 11. Rev. 02 — 14 April 2009 NX3L1T53 EXT = 1.5 V 001aah458 0.9V O 001aag572 Y0 1 switch EXT = 1.5 V 001aah459 © NXP B.V. 2009. All rights reserved ...

Page 14

... Figure 1 4 MHz 0.1 nF see Figure 24 gen Rev. 02 — 14 April 2009 NX3L1T53 Load GND or V (unless otherwise I CC Min Typ [1] Figure 19 - 0.15 - 0.10 - 0.02 - 0.02 - 0.02 [ [1] - Figure ...

Page 15

... GND frequency until dB meter reads 3 dB switch GND Rev. 02 — 14 April 2009 NX3L1T53 CC switch 001aah460 CC switch ...

Page 16

... input 0.5V 0. logic input off GND Rev. 02 — 14 April 2009 NX3L1T53 001aah452 off V ct 001aah453 0. 001aah463 © NXP B.V. 2009. All rights reserved ...

Page 17

... Product data sheet Low-ohmic single-pole double-throw analog switch logic input off on ( Rev. 02 — 14 April 2009 NX3L1T53 Y0 1 switch gen V gen GND 001aad398 off V O 001aah451 © NXP B.V. 2009. All rights reserved ...

Page 18

... Low-ohmic single-pole double-throw analog switch scale 1.05 0.35 0.40 0.6 0.5 0.95 0.27 0.32 REFERENCES JEDEC JEITA - - - MO-252 Rev. 02 — 14 April 2009 NX3L1T53 4 ( EUROPEAN PROJECTION © NXP B.V. 2009. All rights reserved. SOT833-1 ISSUE DATE 07-11-14 07-12- ...

Page 19

... scale 3.1 0.5 0.15 0.6 0.5 1.5 2.9 0.3 0.4 0.05 REFERENCES JEDEC JEITA - - - Rev. 02 — 14 April 2009 NX3L1T53 detail 0.1 0.05 0.05 0.1 EUROPEAN PROJECTION SOT996-2 ISSUE DATE 07-12-18 07-12-21 © NXP B.V. 2009. All rights reserved ...

Page 20

... 1.65 0.35 0.15 0.55 0.5 0.1 1.55 0.25 0.05 REFERENCES JEDEC JEITA MO-255 - - - Rev. 02 — 14 April 2009 NX3L1T53 detail 0.05 0.05 0.05 EUROPEAN PROJECTION SOT902 ISSUE DATE 05-11-25 07-11-14 © NXP B.V. 2009. All rights reserved ...

Page 21

... Transistor-Transistor Logic 15. Revision history Table 14. Revision history Document ID Release date NX3L1T53_2 20090414 • Modifications: Added type number NX3L1T53GD (XSON8U package). • Supply voltage range added (V NX3L1T53_1 20090217 NX3L1T53_2 Product data sheet Low-ohmic single-pole double-throw analog switch Data sheet status Change notice ...

Page 22

... Export might require a prior authorization from national authorities. 16.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. http://www.nxp.com salesaddresses@nxp.com Rev. 02 — 14 April 2009 NX3L1T53 © NXP B.V. 2009. All rights reserved ...

Page 23

... Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2009. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com NX3L1T53 All rights reserved. Date of release: 14 April 2009 Document identifier: NX3L1T53_2 ...

Related keywords