el5181 Intersil Corporation, el5181 Datasheet
el5181
Available stocks
Related parts for el5181
el5181 Summary of contents
Page 1
... The rail-to-rail output swing enables direct connection of the comparator to both CMOS and TTL logic circuits. The latch input of the EL5181 can be used to hold the com- parator output value by applying a low logic level to the pin. The EL5181 is available in the 8-pin SO package and is specified for operation over the full -40° ...
Page 2
... Latch Disable to Low Delay D t Minimum Setup Time S t Minimum Hold Time H t (D) Minimum Latch Disable Pulse Width PW 2 EL5181 Storage Temperature Range . . . . . . . . . . . . . . . . . . -65°C to +150°C Ambient Operating Temperature . . . . . . . . . . . . . . . . -40°C to +85°C -) -0.2V] to [(V +) +0.2V] Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125° -0.2V] to [(V +) +0.2V] Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves S ) +0.2V] SD ...
Page 3
... Positive Supply Current vs Temperature 7.15 7.1 7.05 7 6.95 6.9 6.85 6.8 6.75 6.7 -50 -30 -10 Temperature (°C) Positive Supply Current vs Supply Voltage Input Bias Current vs Temperature -50 -30 -10 Temperature (°C) 3 EL5181 -4.4 -4.5 -4.6 -4.7 -4.8 -4.9 -5 -5.1 -5 -50 5 50mV IN 3 25° ...
Page 4
... Step 50mV 2.2k L 8.5 8 7.5 7 6 4.5 Propagation Delay vs Overdrive ± Step IN 9.5 9 8 EL5181 (Continued 300 400 500 600 V (mV 9 5.5 6 ±V ( ...
Page 5
... Frequency (MHz) Output with 30MHz Input P EL5181 (Continued) Output High Voltage vs Load Current 4.75 4.7 4.65 4.6 4.55 4.5 4.45 = -40° ± -50mV IN 4 Package Power Dissipation vs Ambient Temperature JEDEC JESD51-3 Low Effective Thermal Conductivity Test Board 0 ...
Page 6
... Minimum Hold Time - The minimum time after the negative transition of the latch signal that an input signal must remain H unchanged in order to be acquired and held at the output t (D) Minimum Latch Disable Pulse Width - The minimum time that the latch signal must remain high in order to acquire and hold an PW input signal change 6 EL5181 Compare Compare Latch ...
Page 7
... Positive supply voltage S 2 IN+ Positive input 3 IN- Negative input Negative supply voltage S 5 LATCH Latch input 6 GND Digital ground 7 OUT Output 8 V Digital Supply SD 7 EL5181 FUNCTION IN- Circuit 1 (Reference Circuit 1) Circuit 2 Circuit 3 EQUIVALENT CIRCUIT IN LATCH ...
Page 8
... Input Voltage Considerations The EL5181 input range is specified from 0.1V below V 2.25V below V +. The criterion for the input limit is that the ...
Page 9
... DC average voltage based on the output. The crystal's path provides resonant positive feedback and stable oscillation occurs. Although the EL5181 will give the correct logic output I SD when an input is outside the common mode range, additional delays may occur when operated. Therefore, the DC ...