tc7650 Microchip Technology Inc., tc7650 Datasheet - Page 6

• Manufacturer Part Number: tc7650
• Description: Chopper Stabilized Operational Amplifier
• Manufacturer: Microchip Technology Inc.

TC7650
positive duty cycle is desired for frequencies above
500Hz to ensure transients settle before the internal
switches open.
The external clock input can also be used as a strobe
input. If a strobe signal is connected at the external
clock input so that it is LOW during the time an overload
signal is applied, neither capacitor will be charged. The
leakage currents at the capacitors pins are very low. At
25°C a typical TC7650 will drift less than 10µV/sec.
3.6
Chopper-stabilized systems can show long recovery
times from overloads. If the output is driven to either
supply rail, output saturation occurs. The inputs are no
longer held at a "virtual ground." The V
treats the differential signal as an offset and tries to cor-
rect it by charging the external capacitors. The nulling
circuit also saturates. Once the input signal returns to
normal, the response time is lengthened by the long
recovery time of the nulling amplifier and external
capacitors.
Through an external clamp connection, the TC7650
eliminates the overload recovery problem by reducing
the feedback network gain before the output voltage
reaches either supply rail.
FIGURE 3-3:
FIGURE 3-4:
DS21463B-page 6
*
Input
Connect To V
On 8-Pin DIP.
For Full Clamp Effect
R
3
+ (R1/R2) ‡ 100 kΩ
Output Clamp
Internal
Positive Clamp Bias ≈ V + - V
SS
P-Channel
N-Channel
INTERNAL CLAMP CIRCUIT
NON-INVERTING AMPLIFIER
WITH OPTIONAL CLAMP
+
TC7650
C
Clamp
0.1µF
R
Output
Clamp Pin
*
R
C
3
OS
R
R
T
2
1
≈ V + - 0.7
null circuit
Output
FIGURE 3-5:
The output clamp circuit is shown in Figure 3-3, with
typical inverting and non-inverting circuit connections
shown in Figures 3-4 and 3-5. Output voltage versus
clamp circuit current characteristics are shown in the
typical operating curves. For the clamp to be fully effec-
tive, the impedance across the clamp output should be
greater than 100kΩ.
3.7
Junction-isolated CMOS circuits inherently include a
parasitic 4-layer (p-n-p-n) structure which has charac-
teristics similar to an SCR. Under certain circum-
stances this junction may be triggered into a low-
impedance state, resulting in excessive supply current.
To avoid this condition, no voltage greater than 0.3V
beyond the supply rails should be applied to any pin. In
general, the amplifier supplies must be established
either at the same time or before any input signals are
applied. If this is not possible, the drive circuits must
limit input current flow to under 0.1mA to avoid latch-
up.
3.8
Precision DC measurements are ultimately limited by
thermoelectric potentials developed in thermocouple
junctions of dissimilar metals, alloys, silicon, etc.
Unless all junctions are at the same temperature, ther-
moelectric voltages, typically around 0.1µV/°C, but up
to tens of µV/°C for some materials, will be generated.
In order to realize the benefits extremely-low offset volt-
ages provide, it is essential to take special precautions
to avoid temperature gradients. All components should
be enclosed to eliminate air movement, especially
those caused by power dissipating elements in the sys-
tem. Low thermoelectric co-efficient connections
should be used where possible and power supply volt-
ages and power dissipation should be kept to a mini-
mum. High impedance loads are preferable, and
separation from surrounding heat dissipating elements
is advised.
*
Input
Connect To V
On 8-Pin DIP.
Latch-Up Avoidance
Thermoelectric Potentials
R
1
–
R
INVERTING AMPLIFIER WITH
OPTIONAL CLAMP
©
0.1 F
TC7650
+
C
2002 Microchip Technology Inc.
Clamp
µ
R
0.1 F
*
R
C
2
µ
For Full Clamp
Effect
(R
1
R
2
) ‡ 100 kΩ
Output