xr88c92 Exar Corporation, xr88c92 Datasheet - Page 20

• Manufacturer Part Number: xr88c92
• Description: Xr88c92 -dual Uart With 8 Bytes Transmit And Receive Fifo
• Manufacturer: Exar Corporation

XR88C92/192
following table shows how to select the clock source for
the C/T when used in counter mode or timer mode.
ACR Bit-7: Baud rate table Select.
This bit is used to select between two sets of baud rate
tables. See Baudrate table on Page 18. It should be
changed only after both channels have been reset and
disabled.
0 = Set 1
1 = Set 2
INTERRUPT STATUS REGISTER (ISR)
This register provides the status of all potential interrupt
sources. The contents of this register are logically
“AND”-ed with the contents of the interrupt mask regis-
ter, and the results are “OR”-ed. The resulting signal is
inverted to produce the -INT output. All active interrupt
sources are visible by reading the ISR, regardless of
the contents of the interrupt mask register. Reading
the ISR has no effect on any interrupt source. Each
active interrupt source must be cleared in a source-
specific fashion to clear the ISR. All interrupt sources
are cleared when the XR88C92/192 is
ISR Bit-0: Transmit ready A.
This bit is set when channel A's transmit buffer (FIFO)
is filled below the programmed transmit trigger level (see
MR0A bits 5-4). For example, if a TX trigger level of '4'
is chosen, this bit will be set whenever the TX FIFO has
four or more empty locations. This bit can be cleared by
loading the TX FIFO above the trigger level.
ISR Bit-1: Receive ready A .
This bit is set when channel A's receive buffer (FIFO)
is filled above the programmed receive trigger level
Bits 6:4
ACR
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
Rev. 1.33
Counter
Counter
Counter
Counter
Mode
Timer
Timer
Timer
Timer
C/T
External (IP2)
TXAClk1-Transmit A 1X clock
TXBClk1-Transmit B 1X clock
Crystal or External Clock
(XTAL1/Clk) Divided by 16
External (IP2)
External (IP2) Divided by 16
Crystal or External Clock
(XTAL1/Clk)
Crystal or External Clock
(XTAL1/Clk) Divided by 16
Clock Source
reset.4
20
condition (see MR0A bit-6 and MR1A bit-6). For ex-
ample, if a RX trigger level of '6' is chosen, this bit will
be set whenever the RX FIFO contains six or more
bytes. This bit can be cleared by reading the data out
of the FIFO till it falls below the trigger level.
ISR Bit-2: Channel A change in break.
This bit is set when channel A receiver detects the
beginning or the end of a break condition. It is reset
when the CPU issues a channel A reset break change
interrupt command (CRA bits 7-4 = 0x5).
ISR Bit-3: Counter/Timer (C/T) ready.
In counter mode, this bit is set when the C/T reaches
terminal count. In timer mode, this bit is set each time
the C/T output switches from low to high (rising edge -
see Figure 2). In either mode, this bit is cleared by a stop
counter command.
ISR Bit-4: Transmit ready B.
This bit is set when channel B's transmit buffer (FIFO)
is filled below the programmed transmit trigger level (see
MR0B bits 5-4). For example, if a TX trigger level of '4'
is chosen, this bit will be set whenever the TX FIFO has
four or more empty locations. This bit can be cleared by
loading the TX FIFO above the trigger level.
ISR Bit-5: Receive ready B.
This bit is set when channel B's receive buffer (FIFO)
is filled above the programmed receive trigger level
condition (see MR0B bit-6 and MR1B bit-6). For ex-
ample, if a RX trigger level of '6' is chosen, this bit will
be set whenever the RX FIFO contains six or more
bytes. This bit can be cleared by reading the data out
of the FIFO till it falls below the trigger level.
ISR Bit-6. Channel B change in break.
This bit is set when channel B receiver detects the
beginning or the end of a break condition. It is reset
when the CPU issues a channel B reset break change
interrupt command (CRB bits 7-4 = 0x5).
ISR Bit-7. Input port change status.
This bit is set when a change of state has occurred at
the IP0, IP1, IP2, or IP3 inputs, and that event has been
enabled to cause an interrupt by programming ACR Bits
3-0. This bit is cleared when the CPU reads the input port
change register.
INTERRUPT MASK REGISTER (IMR)
This register selects which bits in the interrupt status
register can cause an interrupt output. If a bit in the
interrupt status register is a “1” and the corresponding