k4t1g084qe Samsung Semiconductor, Inc., k4t1g084qe Datasheet - Page 45

• Manufacturer Part Number: k4t1g084qe
• Description: 1gb E-die Ddr2 Sdram
• Manufacturer: Samsung Semiconductor, Inc.

44. For tAOFD of DDR2-400/533, the 1/2 clock of tCK in the 2.5 x tCK assumes a tCH, input clock HIGH pulse width of 0.5 relative to tCK. tAOF,min and
45. For tAOFD of DDR2-667/800, the 1/2 clock of nCK in the 2.5 x nCK assumes a tCH(avg), average input clock HIGH pulse width of 0.5 relative to
K4T1G084QE
K4T1G164QE
K4T1G044QE
For example, if an input clock has a worst case tCH of 0.45, the tAOFmin should be derated by subtracting 0.05 x tCK from it, whereas if an input clock
For example, if an input clock has a worst case tCH(avg) of 0.48, the tAOFmin should be derated by subtracting 0.02 x tCK(avg) from it, whereas if an
Note that these deratings are in addition to the tAOF derating per input clock jitter, i.e. tJIT(duty) and tERR(6-10per). However tAC values used in the
tAOF,max should each be derated by the same amount as the actual amount of tCH offset present at the DRAM input with respect to 0.5.
has a worst case tCH of 0.55, the tAOFmax should be derated by adding 0.05 x tCK to it. Therefore, we have;
tCK(avg). tAOFmin and tAOFmax should each be derated by the same amount as the actual amount of tCH(avg) offset present at the DRAM input
with respect to 0.5.
input clock has a worst case tCH(avg) of 0.52, the tAOFmax should be derated by adding 0.02 x tCK(avg) to it. Therefore, we have;
equations shown above are from the timing parameter table and are not derated. Thus the final derated values for tAOF are;
tAOFmin(derated) = tAC,min - [0.5 - Min(0.5, tCHmin)] x tCK
tAOFmax(derated) = tAC,max + 0.6 + [Max(0.5, tCHmax) - 0.5] x tCK
or
tAOFmin(derated) = Min(tACmin, tACmin - [0.5 - tCHmin] x tCK)
tAOFmax(derated) = 0.6 + Max(tACmax, tACmax + [tCHmax - 0.5] x tCK)
where tCHmin and tCHmax are the minimum and maximum of tCH actually measured at the DRAM input balls.
tAOFmin(derated) = tACmin - [0.5 - Min(0.5, tCH(avg)min)] x tCK(avg)
tAOFmax(derated) = tACmax + 0.6 + [Max(0.5, tCH(avg)max) - 0.5] x tCK(avg)
tAOFmin(derated) = Min(tACmin, tACmin - [0.5 - tCH(avg)min] x tCK(avg))
tAOFmax(derated) = 0.6 + Max(tACmax, tACmax + [tCH(avg)max - 0.5] x tCK(avg))
where tCH(avg),min and tCH(avg),max are the minimum and maximum of tCH(avg) actually measured at the DRAM input balls.
tAOFmin(derated_final) = tAOFmin(derated) + { - tJIT(duty)max - tERR(6-10per)max }
tAOFmax(derated_final) = tAOFmax(derated) + { - tJIT(duty)min - tERR(6-10per)min }
45 of 45
Rev. 1.1 December 2008
DDR2 SDRAM