ta1316an TOSHIBA Semiconductor CORPORATION, ta1316an Datasheet - Page 27

• Manufacturer Part Number: ta1316an
• Description: Ycbcr/ypbpr Signal And Sync Processor For Digital Tv, Progressive Scan Tv And Double Scan Tv
• Manufacturer: TOSHIBA Semiconductor CORPORATION

BLACK STRETCH POINT
APL VS BSP
B.L.C
B.D.L.
BS-ARE
SHR-TRACKING
WPL-LEVEL
WPL-FREQ
DYNAMIC ABL POINT
DYNAMIC ABL GAIN
ABL POINT
ABL GAIN
RGB-OUT MODE
DYNCγ-POINT
DYNCγ GAIN VS DARK
AREA
STATICγ-GAIN
Y-outγ
OSD BRIGHT
OSD-CONTRAST
Y/C DL1/2
APACON WPL
Parameter
Adjusts black stretch point 1.
Adjusts black stretch point 2.
Turns black level automatic correction on/off.
Max: 8.5 IRE, black stretch has priority.
Switches black detection level.
Turns black stretch area on/off.
SHR tracking (adjusts SRT component gain.)
Adjusts white letter improvement amplitude.
Adjusts white letter improvement start frequency.
Adjusts dynamic ABL detection voltage.
Adjusts dynamic ABL sensitivity.
Adjusts ABL detection voltage.
Adjusts ABL sensitivity.
Switches RGB output mode (switch for RGB output mode for test and adjustment).
Switches dynamic Y γ point.
Turns dynamic Y γ gain VS dark area on/off.
Turns static Y γ dark area gain on/off.
Turns Y-out γ on/off.
Adjusts OSD brightness.
Adjusts OSD contrast.
Adjust Y/C relative phase: Y phase before RGB matrix is changed.
Adjusts APACON white peak limiter.
000: OFF, 001 (34 IRE) ~111 (53 IRE)
00 (0 IRE) ~11 (24 IRE) up
0: Off, 1: On
0: 3 IRE, 1: 0 IRE
0: On, 1: Off
00 (SRT-GAIN max) ~11 (SRT-GAIN min)
000: min 111: max
000 (5 MHz) ~111 (16 MHz)
000 (min) ~111 (max)
000 (min) ~111 (max)
000 (min) ~111 (max)
000 (min) ~111 (max)
00: Normal, 01: R only, 10: G only, 11: B only
00: 20 IRE, 01: 21.5 IRE, 10: 23.5 IRE, 11: 25 IRE
000 (min) ~
111 (max (when 25 IRE or below is 25% or more of area ratio, +3dB) )
00: Off (0dB) 11: max (1.5dB, at this time, DYNCγ gain is +1.5dB max)
0: Off, 1: On
00: 5 IRE, 01: 0 IRE, 10: −5 IRE, 11: −10 IRE
00 (min (−9.5dB) ) ~11 (max (0dB) )
Y/C DL2 = 0 and Y/C DL1 = 0: −10 ns, Y/C DL2 = 0 and Y/C DL1 = 1: −5 ns
Y/C DL2 = 1 and Y/C DL1 = 0: 0 ns, Y/C DL2 = 1 and Y/C DL1 = 1: +5 ns
000 (Off) ~111 (Maximum effect of positive limiter)
27
Explanation
Center
0 IRE
Off
3 IRE
On
Center
min
5 MHz
Center
min
Center
min
Normal
23.5 IRE
min
Off
Off
−5 IRE
min
−10 ns
Off
TA1316AN
2002-10-04
Preset