AD622ARZ-RL7 AD [Analog Devices], AD622ARZ-RL7 Datasheet - Page 11

• Manufacturer Part Number: AD622ARZ-RL7
• Description: Low Cost Instrumentation Amplifier
• Manufacturer: AD [Analog Devices]

GAIN SELECTION
The AD622 gain is resistor programmed by R
precisely, by whatever impedance appears between Pin 1 and
Pin 8. The AD622 is designed to offer gains as close as possible
to popular integer values using standard 1% resistors. Table 5
shows required values of R
G = 1, the R
gain, R
To minimize gain error, avoid high parasitic resistance in series
with R
coefficient less than 10 ppm/°C for the best performance.
Table 5. Required Values of Gain Resistors
Desired
Gain
2
5
10
20
33
40
50
65
100
200
500
1000
INPUT AND OUTPUT OFFSET VOLTAGE
The low errors of the AD622 are attributable to two sources:
input and output errors. The output error is divided by G when
referred to the input. In practice, the input errors dominate at
high gains and the output errors dominate at low gains. The
total V
REFERENCE TERMINAL
The reference terminal potential defines the zero output voltage
and is especially useful when the load does not share a precise
ground with the rest of the system. The reference terminal provides
a direct means of injecting a precise offset to the output, with an
allowable range of 2 V within the supply voltages. Parasitic
resistance should be kept to a minimum for optimum CMR.
INPUT PROTECTION
The AD622 features 400 Ω of series thin film resistance at its
inputs and safely withstands input overloads of up to ±15 V or
±60 mA for up to an hour at room temperature. This is true for
all gains and power on and off, which is particularly important
because the signal source and amplifier can be powered
Total Error RTI = input error + (output error/G)
Total Error RTO = (input error × G) + output error
R
G
G
OS
G
. To minimize gain drift, R
can be calculated by using the formula
=
for a given gain is calculated as follows:
50
G
G
5 .
pins are unconnected (R
−
k
1% Std Table Value of R
51.1 k
12.7 k
5.62 k
2.67 k
1.58 k
1.3 k
1.02 k
787
511
255
102
51.1
1
Ω
G
for various gains. Note that for
G
should have a low temperature
G
= ∞). For any arbitrary
G
, Ω
G
or, more
Calculated
Gain
1.988
4.976
9.986
19.91
32.96
39.85
50.50
65.17
99.83
199.0
496.1
989.3
Rev. D | Page 11 of 16
separately. For longer time periods, the input current should not
exceed 6 mA. For input overloads beyond the supplies, clamping
the inputs to the supplies (using a diode such as a BAV199)
reduces the required resistance, yielding lower noise.
Large Input Voltages at Large Gains
When operating at high gain, large differential input voltages
may cause more than 6 mA of current to flow into the inputs.
This condition occurs when the maximum differential voltage
exceeds the following critical voltage:
This is true for differential voltages of either polarity.
The maximum allowed differential voltage can be increased by
adding an input protection resistor in series with each input.
The value of each protection resistor should be as follows:
RF INTERFERENCE
RF rectification is often a problem when amplifiers are used in
applications where there are strong RF signals. The disturbance
may appear as a small dc offset voltage. High frequency signals
can be filtered with a low-pass, RC network placed at the input
of the instrumentation amplifier, as shown in Figure 18. In
addition, this RC input network also provides additional input
overload protection (see the Input Protection section).
The filter limits the input signal bandwidth to the following
cutoff frequencies:
where C
V
R
FilterFreq
FilterFreq
PROTECT
CRITICAL
Figure 18. RFI Suppression Circuit for AD622 Series In-Amps
D
≥ 10C
= (V
= (400 + R
DIFF
CM
4.02kΩ
4.02kΩ
C
.
R
R
DIFF_MAX
=
=
2
2
π
π
G
1
RC
C
1nF
C
47nF
C
1nF
R
) × (6 mA)
− V
C
D
C
(2
C
C
1
CRITICAL
D
0.1µF
0.1µF
R
+IN
–IN
+
G
C
C
)/6 mA
AD622
)
+V
–V
S
S
10µF
10µF
REF
V
OUT
+
+
AD622