mtc-163-0515 SL Power Electronics, mtc-163-0515 Datasheet - Page 2

• Manufacturer Part Number: mtc-163-0515
• Description: 160, 220 Watts Multiple Output
• Manufacturer: SL Power Electronics

Dimensions:
SPECIFICATIONS: ALL MODELS
INPUT
AC Input: 90-132 Vac/180-264 Vac, 47 to 63 Hz. User selectable. See option “A” for
Inrush: Cold start AC current is less than 16 A at 115 Vac and 32 A at 230 Vac. Limited by
Holdup Time: 16 ms minimum after removal of power, at nominal line, full load.
Efficiency: 75% typical.
Brownout Protection: Holds regulation to 85 Vac or 170 Vac.
OUTPUT
Adjustability: Main output and output #3 user adjustable ±5% minimum. Output #4 (output
Line & Load Reg: ±1% over AC input range and 0 to 100% load change. On MDT series
Ripple & Noise: Less than 1% p-p or 100 mV, whichever is greater.
Remote Sense (+5V): Compensates for 250 mV total line drop. Open sense lead protection.
Temperature Coefficient: 0.02% per degree C.
Stability: 0.1% over 8 hours after 30 minutes warm-up.
Transient Response (+5V): Output voltage returns to within 1% in less than 500 µs for a
Overload Protection: All outputs are protected against overload and short circuit. Automatic
Overvoltage Protection (+5V): Protects load against power supply induced overvoltage. Trip
Reverse Voltage: Protected against reverse voltage up to supply current rating.
ENVIRONMENTAL
Thermal Protection: Shuts down power supply if overheated. Automatic recovery.
Temperature Range: 0° to 50°C at full ratings. Derate to half power at 70 °C.
Safety Agencies: Most models are approved to UL1950; CSA 22.2 #234; IEC 950 and TÜV
Conducted RFI: Meets FCC Part 15, Subpart J, Class A; EN55022 Class B; CISPR 22 Class B.
Output Isolation: Isolated from ground 50 Vdc.
Cooling: 30 CFM required to achieve full ratings. MDT-160 models are convection cooled.
automatic line selection. Internally fused for 7 A.
thermistor.
#3 in MTC series) is not adjustable and has ±5% initial accuracy.
only, output #2 holds ±5% total regulation band, including the combined effects of line
regulation, load regulation for a load change of ±40% from 60% initial load, and cross
regulation due to a load change of ±25% on the 5 V line from 60% initial load. Maximum
combined currents on outputs #1 and 2 cannot exceed output #1 rating, except for
MDT-223-1212R. Main +5 V output requires minimum load of 20% for all models.
50% load change. Peak transient does not exceed 5%.
recovery upon removal of fault.
point is factory set so that output voltage cannot exceed 6.8 V.
EN60950, Class 1 SELV., CE 72/23/EEC/93/68EEC (low voltage directive).
Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • [phone] Fax: [phone] http://www.condorpower.com
Millimeters
Inches
MDT-160, 220
2.6 lbs - 1.2 kgs
OPTIONS:
Option “A”, AC Auto-Range: Automatically selects proper AC line voltage range to enable
Option “P”, AC Power Fail: Provides TTL “0” 5 ms before output voltage goes out of
Consult factory for other available options.
AC INPUT
Note: Return lines (Rtn) are connected to power supply common(COM)
DC OUTPUT
STATUS AND CONTROL
Input Select
TB1-
TB1-
TB1-
Output #1
Output #2
Output #3
Output #4
AC Power Fail
(optional function)
Remote Sense
power operation at either 115 or 230 Vac without user intervention.
regulation band upon loss of AC power. VMEbus compatible, provides 48 mA sink current
capability.
FUNCTION
FUNCTION
FUNCTION
(L )
(N)
( )
Short
Line
Neutral
Safety Ground Safety Ground
Terminal +5
Terminal COM Terminal COM
TB2-3 (+)
TB2-4 (Rtn)
TB2-2 (+)
TB2-1 (Rtn)
Terminal + S
Terminal – S
Terminal PF
MDT-163/223
115 VAC
LOCATION
160, 220 WATTS
9”x 5”x 2.5”
MDT-160, 220 MTC-160
2.6 lbs - 1.2 kgs
Open
Line 1
Line 2
Terminal +5
TB2-4 (+)
TB2-5 (Rtn)
TB2-3(+)
TB2-2 (Rtn)
TB2-1 (–)
TB2-2 (RTN)
MTC-160
MDT-164/224
230 VAC
Output #1 Sense
Output #1 Sense Rtn
Reference to (– S)
NOTES
.110 male Fastons or #16 bus jumper
Barrier strip #6-32 screws
3/8” centers
Terminal +5
Terminal COM
TB2-3 (+)
TB2-2 (Rtn)
TB2-1 (–)
TB2-2 (Rtn)
MTC-163
CONNECTOR
#6-32 screws
CONNECTOR
CONNECTOR
Bus bars
#6-32screws
Barrier strip
#6-32 screws
3/8” centers