LT1105 LINER [Linear Technology], LT1105 Datasheet - Page 11

• Manufacturer Part Number: LT1105
• Description: Offline Switching Regulator
• Manufacturer: LINER [Linear Technology]

LT1103
FB: The Feedback pin is the inverting input to the sampling
error amplifier. The noninverting input is tied to a 4.5V
reference. The FB pin is used for output voltage sensing.
The input bias current is a function of the control pin V
voltage and can be used for load regulation compensation
by including a resistor in series with the FB pin. The
sampling error amplifier has a typical g
and the output of the sampling error amplifier has asym-
metrical slew rate to reduce overshoot during start-up
conditions or following the release of an output overload.
V
tion, current limiting and shutdown. It is the high imped-
ance output of the sampling error amplifier and the input
of the current limit comparator.
GND: The Ground pin acts as both the negative sense
point for the internal sampling error amplifier feedback
signal and as the high current path for the 2A switch.
Also, the case of the 7-lead TO-220 is connected to
ground. Proper connections to ground for signal paths
and high current paths must be made in order to insure
good load regulation.
OSC: The Oscillator pin sets the operating frequency of the
regulator with one external capacitor to ground. Maximum
duty cycle can also be adjusted by using an external
resistor to alter the charge/discharge ratio.
V
voltages of 12V to 30V. The supply current is typically
200 A up to the start-up threshold of 16V. Normal oper-
ating supply current is fairly flat at 18mA down to the
shutdown threshold of 7V. Switching is inhibited for V
less than 12V due to the gate drive detection circuit.
15V: A 15V reference is used to bias the gate of an external
power FET. The voltage temperature coefficient is typically
3mV/ C and the output can source 30mA. Typical dropout
voltage is 1.5V for V
current.
PIN
C
IN
: The V
U
: The Input Supply pin is designed to operate with
FUNCTIONS
C
U
control pin is used for frequency compensa-
IN
U
less than 17V and 30mA of load
m
of 0.012 mhos
IN
C
V
NPN power switch. This pin has a typical ON resistance of
0.4 and a minimum breakdown voltage of 50V. This pin
also ties to the FET gate drive detection circuit.
LT1105
All functions on the LT1105 are equivalent to the LT1103
with the exception of the V
availability of the OVLO, 5V, and SS functions.
OVLO: The Overvoltage Lockout pin inhibits switching
when the pin is pulled above its threshold voltage of 2.5V.
OVLO is implemented with a resistor divider network from
the rectified DC line and is used to protect the external FET
from an overvoltage condition in the off state. This func-
tion is only available on the 14-lead PDIP.
5V: A 5V reference is available to power primary-side
circuitry. The temperature coefficient is typically
50ppm/ C and the output can source 25mA. This func-
tion is only available on the 14-lead PDIP.
SS: The Soft-Start pin is used to either program start-up
time with a capacitor to ground or to set external current
limit with a resistor divider. The SS pin has a 40 A pull-up
current and is reset to 0V by a 1mA pull-down current
during start-up and shutdown. This function is only avail-
able on the 14-lead PDIP.
V
totem-pole stage. The V
pulling its gate high. Break-Before-Make action of 200ns
on each switch edge is built in to eliminate cross conduc-
tion currents.
I
and requires the use of a noninductive, power sense
resistor from I
current limit threshold voltage is 350mV. The typical input
bias current is 100 A out of the pin.
LIM
SW
SW
: The I
: The Switch Output pin is the collector of the internal
: The Switch Output pin is the output of a 1A NPN
LIM
pin is the input to the current limit amplifier
LIM
to ground to set current limit. The typical
SW
SW
pin turns the external FET on by
pin and the I
LT1103/LT1105
LIM
pin and the
11