LT1800IS5 LINER [Linear Technology], LT1800IS5 Datasheet
LT1800IS5
Available stocks
Related parts for LT1800IS5
LT1800IS5 Summary of contents
Page 1
FEATURES Gain Bandwidth Product: 80MHz Input Common Mode Range Includes Both Rails Output Swings Rail-to-Rail Low Quiescent Current: 2mA Max Input Offset Voltage: 350 V Max Input Bias Current: 250nA Max Low Voltage Noise: 8.5nV/ Hz Slew Rate: 25V/ s ...
Page 2
... 2.5V to 10V ORDER PART NUMBER TOP VIEW + LT1800CS5 LT1800IS5 + – 4 –IN S5 PART MARKING S5 PACKAGE LTRN = 150 C, = 250 LTRP MIN TYP MAX 75 350 300 750 0.5 3 0.7 3.5 20 180 25 250 500 ...
Page 3
ELECTRICAL CHARACTERISTICS 5V, 0V 3V, 0V SYMBOL PARAMETER V Output Voltage Swing Low (Note Output Voltage Swing High (Note Short-Circuit Current ...
Page 4
LT1800 ELECTRICAL CHARACTERISTICS of – 5V, 0V 3V, 0V SYMBOL PARAMETER V Input Offset Voltage OS V Input Offset Shift Input Offset Voltage Drift ...
Page 5
ELECTRICAL CHARACTERISTICS 5V 0V 0V, unless otherwise noted OUT SYMBOL PARAMETER A Large-Signal Voltage Gain VOL CMRR Common Mode Rejection Ratio Input Common Mode Range PSRR Power ...
Page 6
LT1800 ELECTRICAL CHARACTERISTICS 5V 0V SYMBOL PARAMETER I Short-Circuit Current SC I Supply Current per Amplifier S GBW Gain Bandwidth Product SR Slew Rate The denotes ...
Page 7
W U TYPICAL PERFOR A CE CHARACTERISTICS V Distribution (SO-8, PNP Stage 5V –250 –150 –50 50 ...
Page 8
LT1800 W U TYPICAL PERFOR A CE CHARACTERISTICS Output Saturation Voltage vs Load Current (Output High 5V 0 125 – ...
Page 9
W U TYPICAL PERFOR A CE CHARACTERISTICS Input Current Noise vs Frequency 3 5V 2.5 2.0 PNP ACTIVE 1 2.5V CM 1.0 NPN ACTIVE 0 4.25V CM 0 0.01 0 ...
Page 10
LT1800 W U TYPICAL PERFOR A CE CHARACTERISTICS Common Mode Rejection Ratio vs Frequency 120 100 0.01 0 100 FREQUENCY (MHz) 1800 G26 Series Output Resistor vs Capacitive ...
Page 11
W U TYPICAL PERFOR A CE CHARACTERISTICS 5V Large-Signal Response 2V/DIV 200ns/DIV 1800 G35 APPLICATIO S I FOR ATIO Circuit Description The LT1800 has an ...
Page 12
LT1800 U U APPLICATIO S I FOR ATIO of Q16 is nominally equal to the base current of the input devices. The base current of Q16 is then mirrored by devices Q17-Q19 to cancel the base current of the input ...
Page 13
U U APPLICATIO S I FOR ATIO diodes should be limited to less than 10mA when they are active. The worst-case differential input voltage usually occurs when the input is driven while the output is shorted to ground in a ...
Page 14
LT1800 U TYPICAL APPLICATIO S 500mV/DIV 50ns/DIV S Figure 3. Current Sense Amplifier Large-Signal Response 909 Single 3V Supply, 1MHz, 4th Order Butterworth Filter The circuit shown in Figure 4 ...
Page 15
PACKAGE DESCRIPTIO 0.62 MAX 3.85 MAX 2.62 REF RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.20 BSC DATUM ‘A’ 0.30 – 0.50 REF NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING ...
Page 16
LT1800 U TYPICAL APPLICATIO Low Power High Voltage Amplifier Certain materials used in optical applications have charac- teristics that change due to the presence and strength electric field. The voltage applied across these materials should be precisely ...