FAN4800_10 FAIRCHILD [Fairchild Semiconductor], FAN4800_10 Datasheet
FAN4800_10
Related parts for FAN4800_10
FAN4800_10 Summary of contents
Page 1
FAN4800 Low Startup Current PFC/PWM Controller Combinations Features Low Startup Current (100µA Typical) Low Operating Current (2.5mA Typical) Low Total Harmonic Distortion, High Power Factor Pin-Compatible Upgrade for the ML4800 Average Current, Continuous or Discontinuous Boost, Leading-Edge PFC Slew Rate ...
Page 2
Block Diagram 16 V EAO 0.3V 2.5V 3. GAIN V RMS MODULATOR 4 I SENSE 3 RAMP1 7 RAMP2 350 8 0. 20μA SS 350 5 V REF DC ...
Page 3
Pin Configuration Pin Definitions Pin # Name 1 I EAO SENSE 4 V RMS RAMP1 (RtCt) 8 RAMP2 (PWM RAMP LIMIT 10 GND 11 PWM OUT ...
Page 4
Absolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be opera- ble above the recommended operating conditions and stressing the parts to these levels is not recommended. In addi- tion, ...
Page 5
Electrical Characteristics Unless otherwise stated, these specifications apply: V Symbol Parameter VOLTAGE ERROR AMPLIFIER V Input Voltage Range FB gm1 Transconductance V (PFC) Feedback Reference Voltage ref Input Bias Current b EAO V (H) Output High-Voltage EAO ...
Page 6
Electrical Characteristics Unless otherwise stated, these specifications apply: V Symbol Parameter PFC I COMPARATOR LIMIT V Threshold Voltage th(cs) (PFC I V LIMIT th(cs) gm Output) (1) t Delay to Output d(pfc_off COMPARATOR LIMIT V ...
Page 7
Electrical Characteristics Unless otherwise stated, these specifications apply: V Symbol Parameter PFC D Minimum Duty Cycle min. D Maximum Duty Cycle max. R (low)1 ON Output Low R dson R (low)2 ON Vol1 Output Low Voltage R (high)1 ON Output ...
Page 8
Typical Performance Characteristics 126 119 112 105 2.0 2.1 2.2 2.3 2.4 2.5 V (V) FB Figure 3. Voltage Error Amplifier (gmv) Transconductance 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0.00 0.0 ...
Page 9
Functional Description The FAN4800 consists of an average-current controlled, continuous boost Power Factor Correction (PFC) front- end and a synchronized Pulse Width Modulator (PWM) back-end. The PWM can be used in either current or voltage mode. In voltage mode, feed ...
Page 10
The output of the voltage error amplifier, V gain modulator responds linearly to variation in V The output of the gain modulator is a current signal, in the form of a full wave rectified sinusoid at twice the line ...
Page 11
V EAO 0.3V 2.5V 3. GAIN V RMS MODULATOR 4 I SENSE 3 RAMP1 7 1.6 Error Amplifier Compensation The PWM loading of the PFC can be modeled as a neg- ative resistor ...
Page 12
Z : Compensation network for the current loop Transconductance EAO V : PFC boost output voltage (typical designed OUTDC value is 380V). The equation uses the worst- case condition to calculate the Z ...
Page 13
Example For the application circuit shown in Figures 12 and 13, with the oscillator running at 100kHz OSC t solving for yields 1. 51.1kΩ, selecting standard components ...
Page 14
Generating V CC After turning on the FAN4800 at 13V, the operating volt- age can vary from 10V to 17.9V. The threshold voltage of the V OVP comparator is 17.9V and its hysteresis is CC 1.5V. When V reaches ...
Page 15
SW2 VIN DC SW1 REF U3 VEAO EA RAMP OSC CLK U4 SW2 VIN DC SW1 U3 VEAO EA REF RAMP OSC CLK U4 © 2005 Fairchild Semiconductor Corporation FAN4800 Rev. 1.0 ...
Page 16
Typical Application Circuit © 2005 Fairchild Semiconductor Corporation FAN4800 Rev. 1.0.6 Figure 12. Current-Mode Application 16 www.fairchildsemi.com ...
Page 17
Typical Application Circuit © 2005 Fairchild Semiconductor Corporation FAN4800 Rev. 1.0.6 (Continued) Figure 13. Voltage-Mode Application 17 www.fairchildsemi.com ...
Page 18
Physical Dimensions 16 1 (0.40) 0.38 MIN 5.33 MAX 2.54 NOTES: UNLESS OTHERWISE SPECIFIED A THIS PACKAGE CONFORMS TO JEDEC MS-001 VARIATION BB B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR ...
Page 19
Fairchild Semiconductor Corporation FAN4800 Rev. 1.0.6 19 www.fairchildsemi.com ...