LT3060EDC LINER [Linear Technology], LT3060EDC Datasheet
LT3060EDC
Available stocks
Related parts for LT3060EDC
LT3060EDC Summary of contents
Page 1
FEATURES n Input Voltage Range: 1.6V to 45V n Output Current: 100mA n Quiescent Current: 40μA n Dropout Voltage: 300mV n Low Noise: 30μV (10Hz to 100kHz) RMS n Adjustable Output 600mV REF n Output Tolerance: ±2% Over ...
Page 2
... LT3060ETS8#PBF LT3060ETS8#TRPBF LT3060ITS8#PBF LT3060ITS8#TRPBF LT3060MPTS8#PBF LT3060MPTS8#TRPBF LT3060HTS8#PBF LT3060HTS8#TRPBF LEAD BASED FINISH TAPE AND REEL LT3060EDC LT3060EDC#TR LT3060IDC LT3060IDC#TR LT3060ETS8 LT3060ETS8#TR LT3060ITS8 LT3060ITS8#TR LT3060MPTS8 LT3060MPTS8#TR LT3060HTS8 LT3060HTS8#TR Consult LTC Marketing for parts specifi ed with wider operating temperature ranges. *The temperature grade is identifi label on the shipping container. ...
Page 3
ELECTRICAL CHARACTERISTICS temperature range, otherwise specifi cations are at T PARAMETER Minimum Input Voltage (Notes 4, 12) ADJ Pin Voltage (Notes 4, 5) Line Regulation (Note 4) Load Regulation (Note 4) Dropout Voltage OUT(NOMINAL) (Notes 6, ...
Page 4
LT3060 ELECTRICAL CHARACTERISTICS temperature range, otherwise specifi cations are at T Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect ...
Page 5
TYPICAL PERFORMANCE CHARACTERISTICS Typical Dropout Voltage 550 500 450 400 T = 125°C 350 J 300 250 T = 25°C J 200 150 100 100 OUTPUT CURRENT (mA) ...
Page 6
LT3060 TYPICAL PERFORMANCE CHARACTERISTICS GND Pin Current vs I LOAD 4 OUT(NOMINAL) 3.5 3.0 2.5 2.0 1.5 1.0 0 100 OUTPUT CURRENT (mA) ...
Page 7
TYPICAL PERFORMANCE CHARACTERISTICS Input Ripple Rejection 100 V = 0.6V 90 OUT OUT 10μF OUT 100mA REF/BYP ...
Page 8
LT3060 TYPICAL PERFORMANCE CHARACTERISTICS RMS Output Noise vs Load Current C = 10nF, C REF/BYP 170 f = 10Hz TO 100kHz 160 C = 10μF 150 OUT 140 V 130 OUT 120 V = 1.8V OUT 110 100 V = ...
Page 9
TYPICAL PERFORMANCE CHARACTERISTICS 5V Transient Response Load Dump OUT V OUT 10mV/DIV V = 12V TO 45V 10V/DIV 2ms/DIV 2.2μF OUT 10nF REF/BYP FF I ...
Page 10
LT3060 PIN FUNCTIONS (DC8/TS8) REF/BYP (Pin 1 / Pin 8): Reference/Bypass. Connecting a single capacitor from this pin to GND bypasses the LT3060’s reference noise and soft-starts the reference. A 10nF bypass capacitor typically reduces output voltage noise to 30μV ...
Page 11
APPLICATIONS INFORMATION The LT3060 is a micropower, low noise, low dropout voltage, 100mA linear regulator with micropower shutdown. The device supplies up to 100mA at a typical dropout voltage of 300mV and operates over a 1.6V to 45V input range. ...
Page 12
LT3060 APPLICATIONS INFORMATION Bypass Capacitance, Output Voltage Noise and Transient Response The LT3060 regulator provides low output voltage noise over the 10Hz to 100kHz bandwidth while operating at full load with the addition of a reference bypass capacitor (C ) ...
Page 13
APPLICATIONS INFORMATION voltages set for greater than 24V, use a minimum output capacitor of 4.7μF. The LT3060 is a micropower device and output load transient response is a function of output capacitance. Larger values of output capacitance decrease the peak ...
Page 14
LT3060 APPLICATIONS INFORMATION Overload Recovery Like many IC power regulators, the LT3060 has safe operating area protection. The safe operating area protection decreases current limit as input-to-output voltage increases, and keeps the power transistor inside a safe operating region for ...
Page 15
APPLICATIONS INFORMATION Table 2. DC Package, 8-Lead DFN COPPER AREA BOARD AREA TOPSIDE* BACKSIDE (mm ) (mm ) (mm ) 2500 2500 2500 1000 2500 2500 225 2500 2500 100 2500 2500 50 2500 2500 *Device is ...
Page 16
LT3060 APPLICATIONS INFORMATION The LT3060 incurs no damage if the ADJ pin is pulled above or below ground by less than 50V. If the input is left open-circuit or grounded, the ADJ pin performs like a large resistor (typically 30k) ...
Page 17
TYPICAL APPLICATION + V > 2.9V IN Paralleling of Regulators for Higher Output Current R1 0.15Ω IN OUT LT3060 C1 2.2μF SHDN ADJ GND REF/BYP C3 1nF R2 0.15Ω IN OUT LT3060 SHDN SHDN ADJ GND REF/BYP C4 1nF R3 ...
Page 18
LT3060 PACKAGE DESCRIPTION 2.55 ±0.05 0.64 ±0.05 1.15 ±0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED PIN 1 BAR TOP MARK (SEE NOTE 6) 0.200 REF 18 DC Package 8-Lead ...
Page 19
PACKAGE DESCRIPTION 0.52 MAX 3.85 MAX 2.62 REF RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.20 BSC DATUM ‘A’ 0.30 – 0.50 REF NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING ...
Page 20
LT3060 RELATED PARTS PART DESCRIPTION NUMBER LT1761 100mA, Low Noise LDO LT1762 150mA, Low Noise LDO LT1763 500mA, Low Noise LDO LT1764/A 3A, Fast Transient Response, Low Noise LDO LT1962 300mA, Low Noise LDO LT1963/A 1.5A Low Noise, Fast Transient ...