LICAL-ENC-HS0011 ETC2 [List of Unclassifed Manufacturers], LICAL-ENC-HS0011 Datasheet - Page 2

• Manufacturer Part Number: LICAL-ENC-HS0011
• Description: HS SERIES ENCODER DATA GUIDE
• Manufacturer: ETC2 [List of Unclassifed Manufacturers]

Table 1: Electrical Specifications
Notes
1. Current consumption with no active loads.
2. For 3V supply, (0.15 x 3.0) = 0.45V max.
3. For 3V supply, (0.8 x 3.0) = 2.4V min.
ABSOLUTE MAXIMUM RATINGS
Table 2: Encoder SEND to Decoder Activation Times (mS)
Page 2
ELECTRICAL SPECIFICATIONS
Parameter
POWER SUPPLY
Operating Voltage
Supply Current:
Power-Down Current:
ENCODER SECTION
Input Low
Input High
Output Low
Output High
Output Sink Current
Output Drive Current
SEND High to DATA_OUT
ENVIRONMENTAL
Operating Temperature Range
At 2.0V V
At 3.0V V
At 5.0V V
At 2.0V V
At 3.0V V
At 5.0V V
Supply Voltage V
Any Input or Output Pin
Max. Current Sourced By Output Pins
Max. Current Sunk By Output Pins
Max. Current Into V
Max. Current Out Of GND
Operating Temperature
Storage Temperature
*NOTE*
damage to the device. Furthermore, extended operation at these maximum
ratings may reduce the life of this device.
CC
CC
CC
CC
CC
CC
Baud Rate
Exceeding any of the limits of this section may lead to permanent
28,800
4,800
CC
CC
Designation
V
I
V
V
I
PDN
V
V
CC
–
–
–
–
CC
OL
OH
IH
IL
0.8 x V
V
CC
Min.
2.0
0.0
-40
–
–
–
–
–
–
–
–
–
–
- 0.7
-0.3
-0.3
-40
-65
CC
Decoder Activation Time
Typical
0.10
0.10
0.20
240
370
670
3.3
–
–
–
–
–
–
–
–
250
300
25
25
to
to V
to
to
0.15 x V
CC
Max.
+125
0.80
0.85
0.95
300
470
780
V
5.5
0.6
+125
+150
67
36
25
25
+6.5
–
–
CC
+ 0.3
CC
Units
VDC
VDC
VDC
mA
mA
mS
µA
µA
µA
µA
µA
µA
°C
V
V
V
V
mA
mA
mA
mA
°C
°C
Notes
–
1
1
1
–
–
–
2
3
–
–
–
–
–
–
RECOMMENDED PAD LAYOUT
Figure 2: HS Series Encoder PCB Layout Dimensions
PRODUCTION CONSIDERATIONS
Figure 3: HS Series Reflow Profile
275
250
225
200
175
150
125
100
75
50
25
0
HS Series encoders and decoders are implemented in an industry standard
20-pin Shrink Small Outline Package (20-SSOP). The recommended layout
dimensions are shown below.
These surface-mount components are designed to comply with standard reflow
production methods. The recommended reflow profile is shown below and
should not be exceeded, as permanent damage to the part may result.
0
20
Lead-Free
Sn / Pb
40
60
*CAUTION*
This product is a static-sensitive component. Always wear an ESD
wrist strap and observe proper ESD handling procedures when
working with this device. Failure to observe this precaution may
result in device damage or failure.
80
(0.41)
0.026
(0.65)
0.016
100
120
140
160
0.047
(1.19)
180
TIME (SECONDS)
200
0.328 (8.33)
0.234 (5.94)
220
240
260
260°C Max
280
240°C Max
300
320
340
360
380
400
420
Page 3