COP8ACC720M9-RE NSC [National Semiconductor], COP8ACC720M9-RE Datasheet - Page 13

• Manufacturer Part Number: COP8ACC720M9-RE
• Description: 8-Bit CMOS OTP Microcontroller with 16k Memory and High Resolution A/D
• Manufacturer: NSC [National Semiconductor]

Oscillator Circuits
Control Registers
CNTRL Register (Address X'00EE)
The Timer1 (T1) and MICROWIRE/PLUS control register
contains the following bits:
PSW Register (Address X'00EF)
The PSW register contains the following select bits:
Bit 7
Bit 7
T1C3
HC
T1C3
T1C2
T1C1
T1C0
MSEL
IEDG
SL1 & SL0
HC
C
T1PNDA Timer T1 Interrupt Pending Flag (Autoreload
T1ENA
EXPND
BUSY
EXEN
FIGURE 7. Crystal and R/C Oscillator Diagrams
C
T1C2
T1PNDA
Half Carry Flag
Carry Flag
RA in mode 1, T1 Underflow in Mode 2, T1A
capture edge in mode 3)
Timer T1 Interrupt Enable for Timer Underflow
or T1A Input capture edge
External interrupt pending
MICROWIRE/PLUS busy shifting flag
Enable external interrupt
Timer T1 mode control bit
Timer T1 mode control bit
Timer T1 mode control bit
Timer T1 Start/Stop control in timer
modes 1 and 2, T1 Underflow Interrupt
Pending Flag in timer mode 3
Selects G5 and G4 as MICROWIRE/PLUS
signals SK and SO respectively
External interrupt edge polarity select
(0 = Rising edge, 1 = Falling edge)
Select the MICROWIRE/PLUS clock divide
by (00 = 2, 01 = 4, 1x = 8)
T1C1
T1ENA
T1C0
EXPND
DS012869-8
DS012869-7
(Continued)
MSEL
BUSY
IEDG
EXEN
SL1
Bit 0
GIE
SL0
Bit 0
13
The Half-Carry flag is also affected by all the instructions that
affect the Carry flag. The SC (Set Carry) and R/C (Reset
Carry) instructions will respectively set or clear both the carry
flags. In addition to the SC and R/C instructions, ADC,
SUBC, RRC and RLC instructions affect the Carry and Half
Carry flags.
ICNTRL Register (Address X'00E8)
The ICNTRL register contains the following bits:
Timers
The device contains a very versatile set of timers (T0 and
T1). All timers and associated autoreload/capture registers
power up containing random data.
TIMER T0 (IDLE TIMER)
The device supports applications that require maintaining
real time and low power with the IDLE mode. This IDLE
mode support is furnished by the IDLE timer T0, which is a
16-bit timer. The Timer T0 runs continuously at the fixed rate
of the instruction cycle clock, t
write to the IDLE Timer T0, which is a count down timer.
The Timer T0 supports the following functions:
is a functional block diagram showing the structure of the
IDLE Timer and its associated interrupt logic.
Bits 11 through 15 of the ITMR register can be selected for
triggering the IDLE Timer interrupt. Each time the selected
bit underflows (every 4k, 8k, 16k, 32k or 64k instruction
cycles), the IDLE Timer interrupt pending bit T0PND is set,
thus generating an interrupt (if enabled), and bit 6 of the Port
G data register is reset, thus causing an exit from the IDLE
mode if the device is in that mode.
In order for an interrupt to be generated, the IDLE Timer in-
terrupt enable bit T0EN must be set, and the GIE (Global In-
terrupt Enable) bit must also be set. The T0PND flag and
T0EN bit are bits 5 and 4 of the ICNTRL register, respec-
tively. The interrupt can be used for any purpose. Typically, it
is used to perform a task upon exit from the IDLE mode. For
more information on the IDLE mode, refer to the Power Save
Modes section.
The Idle Timer period is selected by bits 0–2 of the ITMR
register Bits 3–7 of the ITMR Register are reserved and
should not be used as software flags.
• Exit out of the Idle Mode (See Idle Mode description)
• WATCHDOG logic (See WATCHDOG description)
• Start up delay out of the HALT mode
Reserved
Bit 7
GIE
Reserved This bit is reserved and should be zero.
LPEN
T0PND
T0EN
µWPND
µWEN
T1PNDB
T1ENB
LPEN
Global interrupt enable (enables interrupts)
L Port Interrupt Enable (Multi-Input Wakeup/
Interrupt)
Timer T0 Interrupt pending
Timer T0 Interrupt Enable (Bit 12 toggle)
MICROWIRE/PLUS interrupt pending
Enable MICROWIRE/PLUS interrupt
Timer T1 Interrupt Pending Flag for T1B cap-
ture edge
Timer T1 Interrupt Enable for T1B Input cap-
ture edge
T0PND
T0EN
µWPND
C
. The user cannot read or
µWEN
T1PNDB
www.national.com
T1ENB
Bit 0