FTR-1519-V2 FINISAR [Finisar Corporation.], FTR-1519-V2 Datasheet
FTR-1519-V2
Related parts for FTR-1519-V2
FTR-1519-V2 Summary of contents
Page 1
... Fully metallic enclosure for low EMI • Low power dissipation Finisar’s FTR-1519-V2 1550nm Extended GBIC transceivers have a maximum fiber length of 80 km, and comply with GBIC Specification Revision 5.4 compatible with the Gigabit Ethernet standard as specified in IEEE Draft P802.3z/D5.0 and Fibre Channel FC-PH, PH2, PH3 also available via the 2-wire serial bus specified for Module Definition “ ...
Page 2
... FTR-1519-V2 Extended GBIC Product Specification – November 2007 I. Pin Out Pin Name RX_LOS MOD_DEF(0) MOD_DEF(1) MOD_DEF(2) TX_DISABLE TX_FAULT -RX_DAT +RX_DAT +TX_DAT -TX_DAT Table 1. GBIC to host connector pin assignment “Sequence” indicates the order in which pins make contact when the device is hot plugged. Also see “ ...
Page 3
... FTR-1519-V2 Extended GBIC Product Specification – November 2007 II. Electrical Power Interface Finisar FTR-1519-V2 GBICs have an extended power supply voltage range of 3.15V to 5.5V as described in Table 2. They are compatible with both 5V and 3.3V systems. The GBIC specification calls for a range of only 4.75V to 5.25 volts. The 6V maximum voltage is not allowed for continuous operation, however, TX_FAULT and TX_DISABLE circuitry in Finisar GBICs will function at 6V ...
Page 4
... FTR-1519-V2 Extended GBIC Product Specification – November 2007 Low Speed Signal Parameters Parameter Symbol Min RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis RX_LOS Assert Delay t_loss_on RX_LOS Negate Delay t_loss_off TX_DISABLE Assert Time t_off TX_DISABLE Negate Time t_on TX_DISABLE Reset Time ...
Page 5
... VII. Environmental Specifications Note that the GBIC Specification requires an ambient temperature range of 0°C to +50°C. Finisar FTR-1519-V2 GBICs have an extended range from 0°C to +60°C case temperature as specified in Table 8. Environment ...
Page 6
... FTR-1519-V2 Extended GBIC Product Specification – November 2007 VIII. Serial Communication Protocol All Finisar optical GBICs are ‘Module Definition “4”’ and support the 2 wire serial communication protocol outlined in the GBIC Specification 2 Atmel AT24C01A 128 byte E 2 interfacing with the E PROM, see the Atmel data sheet titled “ ...
Page 7
... FTR-1519-V2 Extended GBIC Product Specification – November 2007 IX. Mechanical Specifications Finisar GBICs are compatible with the mechanical specifications outlined in the GBIC Specification Revision 5.4, Section 6 Insertion, Extraction, and Retention Forces Parameter Symbol Min GBIC insertion GBIC extraction GBIC retention F 130 R Table 10 ...
Page 8
... Serial CMOS E www.Atmel.com *Neither GBIC, FC-PH, nor IEEE802.3 specifies an 80km single mode interface. The FTR-1519-V2 complies with these specifications except for the following optical parameters: laser wavelength, receiver sensitivity, and transmit output power. See Table 6 for details. XI. For More Information ...