MAAP-007649-0001A2 MA-COM [M/A-COM Technology Solutions, Inc.], MAAP-007649-0001A2 Datasheet - Page 2

• Manufacturer Part Number: MAAP-007649-0001A2
• Description: Ultra Linear 2W Power Amplifier 800 to 1000 MHz
• Manufacturer: MA-COM [M/A-COM Technology Solutions, Inc.]

2
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
is considering for development. Performance is based on target specifications, simulated results,
and/or prototype measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available.
Commitment to produce in volume is not guaranteed.
Ultra Linear 2W Power Amplifier
800 to 1000 MHz
1.
2.
3.
4.
5.
MAAP-007649-000100
Electrical Specifications
Operating the MAAP-007649-000100
The MAAM-007649-000100 can be damaged by electrostatic dis-
charge (ESD). Use proper ESD control techniques when handling this
device. To operate the MAAP-007649-000100, follow these steps:
1.) Connect the 50 ohm load
2.) Apply VCC (+7.5 Vdc)
3.) Apply VCONT (+4.4 Vdc)
4.) Set the Input Power Level (P
5.) Turn off in reverse order
Output Return Loss
Frequency Range
Input Return Loss
(2 Tone, ∆F = 1MHz)
Spectral Linearity
Current Variation
All data is based on the Evaluation Circuit Board (page 6), which is tuned specifi-
cally for 860 to 960 MHz (RFID Band), and is attached to a solid metal base for
heat sinking.
NOTE: Improper heat sinking can degrade performance.
The device is capable of operating from 800 to 1000 MHz, with an optimized I/O
match over narrow bands.
DRM Mask: EPC Global Class 1 Generation Dense Reader Mode Spectral Mask
Caution: Operation beyond Absolute Maximum Ratings can degrade
performance or cause permanent damage.
Heat dissipates through several layers between the transistor junctions and metal
baseplate. The PQFN packaged assembly (HBT MMIC die / conductive epoxy /
metal slug interface) is mounted to the application circuit board using SN63
solder. The metal vias in the circuit board dissipate heat to the baseplate.
Control Voltage
Thermal Resistance θ
Junction Temperature Rise Above Baseplate T
Ruggedness
Gain Variation
Parameter
Bias Current
Output P1dB
Bias Supply
Output IP3
Harmonics
Gain
PAE
2
Load VSWR 8:1 max., 0
jc
Pout = +20 dBm / tone, 860 to 960 MHz
Pout = +27 dBm / tone, 860 to 960 MHz
5
- 10
Pout for DRM
Over Temp = -40
o
Pout < 31 dBm , Z
VCONT
VCONT
860 to 960 Band @ P1dB
C to +70
1
Quiescent Current Iccq
@ Pout = 28 to 30 dBm
860 to 930 MHz Band
860 to 930 MHz Band
Test Conditions
Control current Icont
in
(Tc= +25
)
860 to 960 Band
860 to 960 Band
960 MHz Band
960 MHz Band
o
C, @ Pout= +31 dBm
3
Power Amp ON
Power Amp OFF
VCC
Mask compliance
o
o
C, VCONT= 4.4 V, VCC = 7.5 V, Z
C to +85
o
jc
L
to 360
5
= 50 Ω
o
o
C
Phase,
Units
o
MHz
dBm
dBm
dBm
dBm
dBc
C/W
mA
mA
dB
dB
dB
dB
dB
dB
o
%
%
V
V
V
C
.
M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
changes to the product(s) or information contained herein without notice.
Absolute Maximum Ratings
Device Junction Temperature T
• North America Tel: [phone] • Europe Tel: [phone]
• India Tel: [phone]
Duty Cycle without Heat Sink Block
Visit www.macomtech.com for additional data sheets and product information.
Supply Current without RF Drive
Duty Cycle with Heat Sink Block
Supply Current with RF Drive
Control Voltage VCONT
Operating Temperature
Storage Temperature
Supply Voltage VCC
Min
RF Input Power
800
-10
-10
4.1
Parameter
33
46
47
43
-8
Load VSWR
No Permanent Damage
0
= 50 Ω, CW)
16.6
68
J
Typ
30.7
19.5
44.5
, max
• China Tel: [phone]
540
1.3
-15
-15
-11
-48
7.5
4.4
19
34
50
49
o
8
3
o
C/W
C
Absolute Maximum
-65
-40
4
o
o
C to +150
+18 dBm
800 mA
600 mA
C to +85
150
100%
8.5 V
50%
5 V
8:1
Max
1000
o
590
8.5
C
4.7
10
2
6
Rev. V3
o
o
C
C