HS9-1840ARH/PROTO INTERSIL [Intersil Corporation], HS9-1840ARH/PROTO Datasheet - Page 7

• Manufacturer Part Number: HS9-1840ARH/PROTO
• Description: Rad-Hard 16 Channel CMOS Analog Multiplexer with High-Z Analog Input Protection
• Manufacturer: INTERSIL [Intersil Corporation]

Ceramic Metal Seal Flatpack Packages (Flatpack)
NOTES:
10. Controlling dimension: INCH.
1. Index area: A notch or a pin one identification mark shall be located
2. If a pin one identification mark is used in addition to a tab, the limits
3. This dimension allows for off-center lid, meniscus, and glass over-
4. Dimensions b1 and c1 apply to lead base metal only. Dimension M
5. N is the maximum number of terminal positions.
6. Measure dimension S1 at all four corners.
7. For bottom-brazed lead packages, no organic or polymeric materi-
8. Dimension Q shall be measured at the point of exit (beyond the me-
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
b
A
SEATING AND
BASE PLANE
e
adjacent to pin one and shall be located within the shaded area
shown. The manufacturer’s identification shall not be used as a pin
one identification mark. Alternately, a tab (dimension k) may be
used to identify pin one.
of dimension k do not apply.
run.
applies to lead plating and finish thickness. The maximum limits of
lead dimensions b and c or M shall be measured at the centroid of
the finished lead surfaces, when solder dip or tin plate lead finish is
applied.
als shall be molded to the bottom of the package to cover the leads.
niscus) of the lead from the body. Dimension Q minimum shall be
reduced by 0.0015 inch (0.038mm) maximum when solder dip lead
finish is applied.
-C-
-A-
0.004
Q
M
H A - B
L
M
c1
S
E3
SECTION A-A
D
LEAD FINISH
S
METAL
BASE
7
PIN NO. 1
ID AREA
E2
b1
(b)
E1
E
M
E3
0.036
(c)
HS-1840ARH, HS-1840BRH
M
-D-
L
H A - B
S1
C
-B-
S
A
A
D
-H-
S
D
K28.A
28 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE
SYMBOL
E1
E2
E3
S1
b1
c1
Q
M
A
D
E
N
b
c
e
k
L
MIL-STD-1835 CDFP3-F28 (F-11A, CONFIGURATION B)
0.045
0.015
0.015
0.004
0.004
0.460
0.180
0.030
0.008
0.250
0.026
0.00
MIN
-
-
-
0.050 BSC
INCHES
28
0.115
0.022
0.019
0.009
0.740
0.520
0.550
0.015
0.370
0.045
0.0015
0.006
MAX
-
-
-
11.68
1.14
0.38
0.38
0.10
0.10
4.57
0.76
0.20
6.35
0.66
0.00
MIN
MILLIMETERS
-
-
-
1.27 BSC
28
18.80
13.21
13.97
2.92
0.56
0.48
0.23
0.15
0.38
9.40
1.14
0.04
MAX
-
-
-
September 14, 2010
Rev. 0 5/18/94
NOTES
FN4355.3
3
3
7
2
8
6
-
-
-
-
-
-
-
-
-
-
-