HFDOM40KB016 HANBIT [Hanbit Electronics Co.,Ltd], HFDOM40KB016 Datasheet - Page 10

• Manufacturer Part Number: HFDOM40KB016
• Description: 40Pin Flash Disk Module Min.8MB ~ Max.1GB, True IDE Interface Mode, 3.3V / 5.0V Operating
• Manufacturer: HANBIT [Hanbit Electronics Co.,Ltd]

HANBit
REGISTERS
URL:www.hbe.co.kr
Rev. 1.1 (December, 2003)
1) Data Register (Address – 1F0h[170h];Offset 0,8,9)
The Data Register is a 16-bit register, and it is used to transfer data blocks between the
CompactFlash Storage Card data buffer and the Host. This register overlaps the Error Register.The table below
describes the combinations of data register access and is provided to assist in understanding the overlapped Data
Register and Error/Feature Register rather than to attempt to define general PCMCIA word and byte access modes
and operations. See the PCMCIA PC Card Standard Release 2.0 for definitions of the Card Accessing Modes for
I/O and Memory cycles.
Note: Because of the overlapped registers, access to the 1F1h, 171h or offset 1 are not defined for word (-CE2 = 0
and -CE1 = 0) operations. These accesses are treated as accesses to the Word Data
Register. The duplicated registers at offsets 8, 9 and Dh have no restrictions on the operations that
can be performed by the socket.
Word Data Register
Even Data Register
Odd Data Register
Odd Data Register
Error/Feature Register
Error/Feature Register
Error/Feature Register
2) Error Register (Address – 1F1h[171h];Offset 1,0Dh Read Only)
This register contains additional information about the source of an error when an error is
indicated in bit 0 of the Status register. The bits are defined as follows:
This register is also accessed on data bits D15-D8 during a write operation to offset 0 with -CE2 low and -CE1 high.
Bit 7 (BBK): this bit is set when a Bad Block is detected.
Bit 6 (UNC): this bit is set when an Uncorrectable Error is encountered.
Bit 5: this bit is 0.
Bit 4 (IDNF): the requested sector ID is not valid error or cannot be found.
Bit 3: this bit is 0.
Bit 2 (Abort) This bit is set if the command has been aborted because of a CompactFlash
Storage Card status condition: (Not Ready, Write Fault, etc.) or when an invalid command
has been issued.
Bit 1 This bit is 0.
Bit 0 (AMNF) This bit is set in case of a general error happened.
3) Feature Register(Address – 1F1h[171h];Offset 1,0Dh Writer Only)
This register provides information regarding features of the CompactFlash Storage Card that the host can utilize.
This register is also accessed on data bits D15-D8 during a write operation to Offset 0 with -CE2 low and -CE1 high.
BIT DESCRIPTION-
4) Sector Count Register(Address – 1F2h[172h];Offset 2)
BBK
DATA Register
D7
7
UNC
D6
6
CE2-
1
0
1
0
0
1
0
D5
0
5
Data Register Access
CE1-
0
0
0
1
0
1
0
Error Register
Command specific
IDNF
D4
4
10 / 10
A0
X
X
X
X
0
1
1
D3
0
3
Offset
0,8,9
1,Dh
0,8
8,9
Dh
9
1
ABRT
D2
2
HFDOM40KVxxx
D1
HANBit Electronics Co., Ltd.
0
1
Data Bus
D15-D0
D15-D8
D15-D8
D15-D8
D7-D0
D7-D0
D7-D0
AMNF
D0
0