LC898113 SANYO [Sanyo Semicon Device], LC898113 Datasheet

LC898113

Manufacturer Part Number

LC898113

Description

OIS Controller & Driver

Manufacturer

SANYO [Sanyo Semicon Device]

Datasheet

1.LC898113.pdf (7 pages)

Current page: 1 of 7
Download datasheet (162Kb)

Ordering number : ENA2130A

LC898113

Overview

The LC898113-TBM-H and LC898113RA-WH (referred to collectively as the LC898113 in this data sheet) are devices

integrating digital gyro interface, gyro filter, stepping motor control circuit, and motor driver functions needed to

implement an image stabilization system using stepping motors. These functions make it possible to build a system

using a minimal software program that enables the host microcontroller to turn image stabilization on and off, for

example.

The gyro filter coefficients may be set to any values by the host microcontroller, making it possible to build filter

circuits optimized for the system. The LC898113 integrates a signal determination circuit for pan/tilt processing and a

filter circuit, enabling implementation of a variety of processing in response to camera movements.

The LC898113 integrates four saturation-drive H-bridge channels for stepping motor drive, and PWM drive with 1-2-

phase control to 8W1-2-phase control is supported.

Also integrated are a photo sensor drive circuit for control object position detection (for example, a CMOS sensor), a

position determination circuit, and a circuit for moving to the optical center based on the results from the preceding

circuits. Thus, the host microcontroller can specify detection start and the LC898113 will automatically move the

control object to the initial position.

Both SPI and I

customer to choose based on the specifications of the host microcontroller. The I

interface.

* I

C Bus is a trademark of Philips Corporation.

"standard application", intended for the use as general electronics equipment. The products mentioned herein

Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to

shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life,

aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system,

safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives

in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any

guarantee thereof. If you should intend to use our products for new introduction or other application different

from current conditions on the usage of automotive device, communication device, office equipment, industrial

equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the

intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely

responsible for the use.

Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate

the performance, characteristics, and functions of the described products in the independent state, and are not

guarantees of the performance, characteristics, and functions of the described products as mounted in the

customer

device, the customer should always evaluate and test devices mounted in the customer

equipment.

C are supported as serial interfaces for communication with the host microcontroller. This allows the

s products or equipment. To verify symptoms and states that cannot be evaluated in an independent

CMOS LSI

OIS Controller & Driver

O3112HK/O0312HKPC 20111207-S00001 No.A2130-1/7

C interface also supports a 1.8 V

s products or

Related parts for LC898113

LC898113 Summary of contents

Page 1

... The gyro filter coefficients may be set to any values by the host microcontroller, making it possible to build filter circuits optimized for the system. The LC898113 integrates a signal determination circuit for pan/tilt processing and a filter circuit, enabling implementation of a variety of processing in response to camera movements. ...

Page 2

... FLGA49 (4mm  4mm) Lead free Halogen free  Power supply voltage (Typical voltage) Logic LSI : Pin 3.3V, Inside 1.8V (External supply required) Driver LSI : VM 5.0V 3.3V Electrical Characteristics Difference between LC898113-TBM-H and LC898113RA-WH a*) : LC898113-TBM-H b*) : LC898113RA-WH Absolute Maximum Ratings Parameter Symbol Power supply voltage ...

Page 3

... Low-level input voltage V IL High-level input voltage V IH Low-level input voltage V IL *Applicable pin (1)ZRESET (2)CLKIN (3)SCLK, MOSI Package Dimensions unit : mm (typ) 3441 TOP VIEW SIDE VIEW 4.0 SIDE VIEW LC898113 Conditions min CMOS schmidt CMOS schmidt CMOS schmidt BOTTOM VIEW 0 0.3 0.5 SANYO : FLGA49(4 ...

Page 4

... MOSI/I2CDT MISO/IOP5/MOND DSP BUSY1/IOP4/MONC BUSY2/IOP3/MOND DGSSB DGSCLK Digital DGMISO Gyro DGMOSI DGINT/IOP2/MONC TEST LC898113 PI1 PI Sensor Digital Filter Block I/F SPI I I/F (Slave) BUSY Pan-Tilt Stepping Driver I/F Digital Gyro I/F Gyro- ...

Page 5

... MODE0 I MODE1 I Test pin TEST I Power supply pin LC898113 TYPE Power, GND NC NOT CONNECT SPI chip select slave address select (L: 0100100, H: 0100101, Please make sure to connect the pin to L level or H level.) 2 SPI clock/I C clock 2 ...

Page 6

... Top View 7 OUT7 OUT8 6 OUT6 5 OUT5 4 OUT4 DGINT 3 OUT3 2 OUT2 1 PGND1 OUT1 A LC898113 Motor control pulse output Motor power supply Other power supply Signal ground Power ground Photo sensor connectiong pin PGND2 VM2 DGMISO ZRESET DV SS DGSSB ...

Page 7

... SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of October, 2012. Specifications and information herein are subject to change without notice. LC898113 PS No.A2130-7/7 ...

Related keywords

LC898113 datasheet
LC898113 data sheet
LC898113 pdf datasheet
LC898113 component
LC898113 part
LC898113 distributor
LC898113 RoHS
LC898113 datasheet download