AMS317A ADMOS [Advanced Monolithic Systems], AMS317A Datasheet - Page 3

• Manufacturer Part Number: AMS317A
• Description: 1A LOW DROPOUT VOLTAGE REGULATOR
• Manufacturer: ADMOS [Advanced Monolithic Systems]

Note 1:
Electrical Characteristics
operating temperature range.
Note 2:
and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range.
Note 3:
temperature by low duty cycle pulse testing. Load regulation is measured at the output lead ~1/8” from the package.
Note 4:
to regulate if the output current is greater than 10mA.
APPLICATION HINTS
The AMS317 series of adjustable and fixed regulators are easy to
use and are protected against short circuit and thermal overloads.
Thermal protection circuitry will shut-down the regulator should
the junction temperature exceed 165 C at the sense point.
Pin compatible with older three terminal adjustable regulators,
these devices offer the advantage of a lower dropout voltage,
more precise reference tolerance and improved reference stability
with temperature.
Stability
The circuit design used in the AMS317 series requires the use of
an output capacitor as part of the device frequency compensation.
The addition of
tantalum on the output will ensure stability for all operating
conditions.
When the adjustment terminal is bypassed with a capacitor to
improve the ripple rejection, the requirement for an output
capacitor increases. The value of 22 F tantalum or
aluminum covers all cases of bypassing the adjustment terminal.
Without bypassing the adjustment terminal smaller capacitors can
be used with equally good results.
To ensure good transient response with heavy load current
changes capacitor values on the order of 100 F are used in the
output of many regulators. To further improve stability and
transient response of these devices larger values of output
capacitor can be used.
Protection Diodes
Unlike older regulators, the AMS317 family does not need any
protection diodes between the adjustment pin and the output and
from the output to the input to prevent over-stressing the die.
Internal resistors are limiting the internal current paths on the
AMS317 adjustment pin, therefore even with capacitors on the
adjustment pin no protection diode is needed to ensure device
safety under short-circuit conditions.
Diodes between the input and output are not usually needed.
Microsecond surge currents of 50A to 100A can be handled by the
internal diode between the input and output pins of the device. In
normal operations it is difficult to get those values of surge
currents even with the use of large output capacitances. If high
value
Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone [phone] Fax [phone]
Line and Load regulation are guaranteed up to the maximum power dissipation of 1.2 W. Power dissipation is determined by the input/output differential
Minimum load current is defined as the minimum output current required to maintain regulation. When 3V
See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. For guaranteed specifications and test conditions, see the
150
.
F aluminum electrolytic or a 22 F solid
The guaranteed specifications apply only for the test conditions listed. Parameters identified with boldface type apply over the full
150
F
output capacitors are used, such as 1000 F to 5000 F and the
input pin is instantaneously shorted to ground, damage can occur.
A diode from output to input is recommended, when a crowbar
circuit at the input of the AMS317 is used (Figure 1).
Output Voltage
The AMS317 series develops a 1.25V reference voltage between
the output and the adjust terminal. Placing a resistor between
these two terminals causes a constant current to flow through R1
and down through R2 to set the overall output voltage. This
current is normally the specified minimum load current of 10mA.
Because I
error and it can usually be ignored.
V
V
IN
IN
ADJ
Figure 2. Basic Adjustable Regulator
is very small and constant it represents a small
V
OUT
IN
= V
AMS317
IN
I
50 A
(V
AMS317
ADJ
ADJ
REF
D1
IN
Figure 1.
ADJ
OUT
- V
1+ R2/R1)+I
C
10 F
OUT
ADJ
OUT
)
25V the device is guaranteed
V
REF
R
R
AMS317
ADJ
1
2
R2
+
R1
R2
C
V
150 F
OUT
OUT
V
OUT