ISL3232EIRZ-T7A Intersil, ISL3232EIRZ-T7A Datasheet - Page 14

• Manufacturer Part Number: ISL3232EIRZ-T7A
• Description: RS-232 Interface IC 3V RS-232 2TX/2RX -4 0+85 TRANS 16LD 5X5
• Manufacturer: Intersil

Specifications of ISL3232EIRZ-T7A

• Product Category: RS-232 Interface IC
• Rohs: yes
• Data Rate: 250 Kbps
• Operating Supply Voltage: 2.7 V to 5.5 V
• Supply Current: 1 uA
• Operating Temperature Range: - 40 C to + 85 C
• Mounting Style: SMD/SMT
• Package / Case: QFN-16
• Function: Transceiver
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Number Of Drivers: 2
• Number Of I/os: 2
• Number Of Receivers: 2
• Shutdown: Yes

Quad Flat No-Lead Plastic Package (QFN)
Micro Lead Frame Plastic Package (MLFP)
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
For information regarding Intersil Corporation and its products, see www.intersil.com
14
ISL3232E, ISL4221E, ISL4223E
L20.5x5
20 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
NOTES:
10. Compliant to JEDEC MO-220VHHC Issue I except for the "b"
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
3. Nd and Ne refer to the number of terminals on each D and E.
4. All dimensions are in millimeters. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
6. The configuration of the pin #1 identifier is optional, but must be
7. Dimensions D2 and E2 are for the exposed pads which provide
8. Nominal dimensions are provided to assist with PCB Land Pattern
9. Features and dimensions A2, A3, D1, E1, P & θ are present when
SYMBOL
between 0.15mm and 0.30mm from the terminal tip.
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
improved electrical and thermal performance.
Design efforts, see Intersil Technical Brief TB389.
Anvil singulation method is used and not present for saw
singulation.
dimension.
A1
A2
A3
D1
D2
E1
E2
Nd
Ne
A
D
E
N
P
b
e
k
L
θ
0.80
0.23
2.95
2.95
0.20
0.35
MIN
-
-
-
-
MILLIMETERS
NOMINAL
5.00 BSC
4.75 BSC
5.00 BSC
4.75 BSC
0.20 REF
0.65 BSC
0.90
0.02
0.65
0.30
3.10
3.10
0.60
20
5
5
-
-
-
MAX
1.00
0.05
1.00
0.38
3.25
3.25
0.75
0.60
12
-
Rev. 4 11/04
May 13, 2010
NOTES
FN6045.6
5, 8
7, 8
7, 8
9
9
9
9
8
2
3
3
9
9
-
-
-
-
-
-