ISL3159EIUZ-T7A Intersil, ISL3159EIUZ-T7A Datasheet - Page 6

• Manufacturer Part Number: ISL3159EIUZ-T7A
• Description: RS-422/RS-485 Interface IC RS-485 IEC-61000 ISL 3159E1/2DUP5V40MBP
• Manufacturer: Intersil

Specifications of ISL3159EIUZ-T7A

• Product Category: RS-422/RS-485 Interface IC
• Rohs: yes
• Data Rate: 40 Mbps
• Operating Supply Voltage: 5 V
• Supply Current: 4 mA
• Operating Temperature Range: - 40 C to + 125 C
• Mounting Style: SMD/SMT
• Package / Case: MSOP-8
• Function: Transceiver
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Shutdown: Yes

Test Circuits and Waveforms
Electrical Specifications
NOTES:
10. These IC’s are put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 60ns, the parts are guaranteed not
12. Set the RE signal high time >700ns to ensure that the device enters SHDN.
13. This is the part-to-part skew between any two units tested with identical test conditions (Temperature, V
14. V
15. Parts are 100% tested at +25°C. Over temperature limits established by characterization and are not production tested.
11. Keep RE = VCC, and set the DE signal low time >700ns to ensure that the device enters SHDN.
Receiver Enable to Output Low
Receiver Disable from Output
High
Receiver Disable from Output
Low
Time to Shutdown
Receiver Enable from Shutdown
to Output High
Receiver Enable from Shutdown
to Output Low
5. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless
6. Supply current specification is valid for loaded drivers when DE = 0V.
7. Applies to peak current. See “Typical Performance Curves” for more information.
8. Because of the shutdown feature, keep RE = 0 to prevent the device from entering SHDN.
9. Because of the shutdown feature, the RE signal high time must be short enough (typically <100ns) to prevent the device from entering SHDN.
otherwise specified.
to enter shutdown. If the inputs are in this state for at least 700ns, the parts are guaranteed to have entered shutdown. See “Low-Power
Shutdown Mode” section.
CC
V
CC
= 5V ±5%
PARAMETER
DE
DI
FIGURE 1A. V
D
Z
Y
6
OD
V
t
Test Conditions: V
(Note 5) (Continued)
t
SYMBOL
ZH(SHDN)
ZL(SHDN)
OD
t
SHDN
AND V
t
t
t
HZ
ZL
LZ
OC
R
R
R
(Note 9)
R
R
(Note 10)
R
(Notes 10, 12)
R
(Notes 10, 12)
L
L
L
L
L
L
L
/2
/2
= 1kΩ, C
= 1kΩ, C
= 1kΩ, C
= 1kΩ, C
= 1kΩ, C
FIGURE 1. DC DRIVER TEST CIRCUITS
CC
V
OC
= 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V
L
L
L
L
L
TEST CONDITIONS
= 15pF, SW = V
= 15pF, SW = GND (Figure 6)
= 15pF, SW = V
= 15pF, SW = GND (Figure 6),
= 15pF, SW = V
ISL3159E
CC
CC
CC
V
CC
(Figure 6),
(Figure 6)
(Figure 6),
DE
DI
FIGURE 1B. V
D
TEMP
(°C)
Full
Full
Full
Full
Full
Full
Z
Y
OD
(NOTE 15)
WITH COMMON MODE LOAD
MIN
CC
60
V
-
-
-
-
-
OD
, etc.).
TYP
CC
-
-
-
-
-
-
R
L
= 5V, T
= 60Ω
(NOTE 15) UNITS
MAX
1000
1000
A
600
12
12
12
= +25°C,
375Ω
375Ω
-7V TO +12V
July 26, 2007
FN6364.0
V
ns
ns
ns
ns
ns
ns
CM