AT24C16B-TSU-T Atmel, AT24C16B-TSU-T Datasheet
AT24C16B-TSU-T
Specifications of AT24C16B-TSU-T
Related parts for AT24C16B-TSU-T
AT24C16B-TSU-T Summary of contents
Page 1
... Die Sales: Wafer Form, Tape and Reel, and Bumped Wafers 2. Description The AT24C16B provides 16384 bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 2048 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential ...
Page 2
... Storage Temperature .....................................–65°C to +150°C Voltage on Any Pin with Respect to Ground .................................... –1.0V to +7.0V Maximum Operating Voltage .......................................... 6.25V DC Output Current........................................................ 5.0 mA Figure 2-1. Block Diagram VCC GND WP SCL SDA AT24C16B 2 *NOTICE: START STOP LOGIC SERIAL CONTROL LOGIC LOAD COMP DEVICE ADDRESS ...
Page 3
... Table 3-1. WP Pin Status GND 4. Memory Organization AT24C16B, 16K SERIAL EEPROM: Internally organized with 128 pages of 16 bytes each, the 16K requires an 11-bit data word address for random word addressing. 5175E–SEEPR–3/09 Table 3-1. Write Protect Part of the Array Protected ...
Page 4
... Input High Level IH V Output Low Level OL1 V Output Low Level OL2 Notes min and V max are reference only and are not tested AT24C16B 4 = 25° 1.0 MHz −40°C to +85° Test Condition V = 5.0V READ at 400 kHz 5.0V WRITE at 400 kHz ...
Page 5
Table 4-3. AC Characteristics (Industrial Temperature) Applicable over recommended operating range from T erwise noted). Test conditions are listed in Note 2. Symbol Parameter f Clock Frequency, SCL SCL t Clock Pulse Width Low LOW t Clock Pulse Width High ...
Page 6
... EEPROM in 8-bit words. The EEPROM sends a zero to acknowledge that it has received each word. This happens during the ninth clock cycle. STANDBY MODE: The AT24C16B features a low-power standby mode which is enabled: (a) upon power-up and (b) after the receipt of the STOP bit and the completion of any internal operations ...
Page 7
Bus Timing Figure 6-1. SCL: Serial Clock, SDA: Serial Data I/O SCL t SU.STA SDA IN SDA OUT 7. Write Cycle Timing Figure 7-1. SCL: Serial Clock, SDA: Serial Data I/O SCL SDA 8th BIT WORDn Note: 1. The ...
Page 8
... Figure 7-2. Data Validity SDA SCL Figure 7-3. Start and Stop Definition SDA SCL Figure 7-4. Output Acknowledge SCL DATA IN DATA OUT AT24C16B 8 DATA STABLE DATA STABLE DATA CHANGE START 1 START STOP 8 9 ACKNOWLEDGE 5175E–SEEPR–3/09 ...
Page 9
... The device address word consists of a mandatory one, zero sequence for the first four most sig- nificant bits as shown. This is common to all the EEPROM devices. The next 3 bits used for memory page addressing and are the most significant bits of the data word address which follows. ...
Page 10
... The sequential read operation is terminated when the microcontroller does not respond with a zero but does generate a following stop condition (see Figure 10-1. Device Address AT24C16B 10 Figure 10-5 on page 12). ...
Page 11
Figure 10-2. Byte Write Figure 10-3. Page Write Figure 10-4. Current Address Read 5175E–SEEPR–3/09 11 ...
Page 12
... Figure 10-5. Random Read Figure 10-6. Sequential Read AT24C16B 12 5175E–SEEPR–3/09 ...
Page 13
... AT24C16B Ordering Information Ordering Codes AT24C16B-PU (Bulk Form Only) AT24C16BN-SH-B (1) (NiPdAu Lead Finish) (2) AT24C16BN-SH-T (NiPdAu Lead Finish) (1) AT24C16B-TH-B (NiPdAu Lead Finish) AT24C16B-TH-T (2) (NiPdAu Lead Finish) (2) AT24C16BY6-YH-T (NiPdAu Lead Finish) (2) AT24C16BD3-DH-T (NiPdAu Lead Finish) AT24C16BTSU-T (2) AT24C16BU3-UU-T (2) AT24C16B-W-11 (3) Notes: 1. “-B” denotes bulk. ...
Page 14
... Part Marking 11.1 8-PDIP TOP MARK |---|---|---|---|---|---|---|---| A |---|---|---|---|---|---|---|---| 1 |---|---|---|---|---|---|---|---| * |---|---|---|---|---|---|---|---| | Pin 1 Indicator (Dot SEAL YEAR 6: 2006 7: 2007 8: 2008 9: 2009 Lot Number to Use ALL Characters in Marking BOTTOM MARK AT24C16B 14 Seal Year | Seal Week | | | Lot Number WW = SEAL WEEK 0: 2010 02 = Week 2 1: 2011 04 = Week 4 2: 2012 :: : :::: : ...
Page 15
TOP MARK |---|---|---|---|---|---|---|---| A |---|---|---|---|---|---|---|---| 1 |---|---|---|---|---|---|---|---| * |---|---|---|---|---|---|---|---| | Pin 1 Indicator (Dot SEAL YEAR 6: 2006 7: 2007 8: 2008 9: 2009 Lot Number to Use ALL Characters in Marking BOTTOM MARK 5175E–SEEPR–3/09 Seal ...
Page 16
... TOP MARK BOTTOM MARK |---|---|---|---|---|---|---| |---|---|---|---|---|---|---| |---|---|---|---|---|---|---| Y = SEAL YEAR 6: 2006 7: 2007 8: 2008 9: 2009 AT24C16B 16 Pin 1 Indicator (Dot) | |---|---|---|---| * |---|---|---|---|---| |---|---|---|---|---| <- Pin 1 Indicator WW = SEAL WEEK 0: 2010 02 = Week 2 1: 2011 04 = Week 4 2: 2012 :: : :::: : 3: 2013 :: : :::: :: 50 = Week Week 52 5175E–SEEPR–3/09 ...
Page 17
... XX = ATMEL LOT NUMBER TO COORESPOND WITH NSEB TRACE CODE LOG BOOK. (e. AA, AB, AC,...AX, AY, AZ SEAL YEAR 6: 2006 7: 2007 8: 2008 9: 2009 11.5 8-ULA TOP MARK Y = BUILD YEAR 2006 2007 XX = ATMEL LOT NUMBER TO COORESPOND WITH (e. AA, AB, AC,...AX, AY, AZ) 5175E–SEEPR–3/09 |---|---|---| |---|---|---| H 1 |---|---|---| |---|---|---| ...
Page 18
... NUMBERS TO CORRESPOND WITH ATK TRACE CODE LOG BOOK) 11.7 SOT23 TOP MARK |---|---|---|---|---| Line 1 -----------> |---|---|---|---|---| * | XXX = Device V = Voltage Indicator U = Material Set Pin 1 Indicator (Dot) BOTTOM MARK |---|---|---|---| |---|---|---|---| Y = One Digit Year Code M = Seal Month (Use Alpha Designator A- Trace Code AT24C16B 18 16BU PYMTC 5175E–SEEPR–3/09 ...
Page 19
Packaging Information 12.1 8P3 – PDIP Top View PLCS Side View Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information. 2. Dimensions A and L ...
Page 20
... JEDEC SOIC Top View e Side View Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R AT24C16B TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing ...
Page 21
TSSOP Pin 1 indicator this corner N Top View Side View Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, ...
Page 22
... Soldering the large thermal pad is optional, but not recommended. No electrical connection is accomplished to the device through this pad soldered it should be tied to ground 2325 Orchard Parkway San Jose, CA 95131 R AT24C16B 22 A Pin 1 Pin 1 Index ...
Page 23
SOT23 E1 1 Seating Plane NOTES: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-193, Variation AB, for additional information. 2. Dimension D does not include mold flash, protrusions, or gate burrs. Mold ...
Page 24
... Bottom View 8 SOLDER BALLS 1. Dimension “b” is measured at the maximum solder ball diameter. This drawing is for general information only. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R AT24C16B TITLE 8U3-1, 8-ball, 1.50 x 2.00 mm Body, 0.50 mm pitch, Small Die Ball Grid Array Package (dBGA2) 1 ...
Page 25
ULA PIN # TOP VIEW 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R 5175E–SEEPR–3/ SIDE VIEW SYMBOL ...
Page 26
... Date Comment 3/2009 Changed the Vcc to 5.5V in the test condition for Isb1 6/2008 Deleted A0, A1, A2 pin-outs AT24C16B product with date code 742 or later supports 5Vcc operation 11/2007 Added ULA package information Removed reference to Waffle Pack 4/2007 Corrected Note 3 on Page 13 Added lines to Ordering Code table ...
Page 27
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...