AT49BV8011-11CI Atmel, AT49BV8011-11CI Datasheet
AT49BV8011-11CI
Specifications of AT49BV8011-11CI
Related parts for AT49BV8011-11CI
AT49BV8011-11CI Summary of contents
Page 1
... Data Inputs/Outputs I/O15 (Data Input/Output, Word Mode) I/O15 (A-1) A-1 (LSB Address Input, Byte Mode) BYTE Selects Byte or Word Mode NC No Connect VCCQ Output Power Supply 8-megabit (512K x 16/ 3-volt Only Flash Memory AT49BV8011 AT49BV8011T AT49LV8011 AT49LV8011T (continued) Rev. 1265E–01/00 1 ...
Page 2
... There is no reason to suspend the erase operation if the data to be read is in the other memory plane. The end of a program or an Erase cycle is detected by the Ready/Busy pin, Data polling the toggle bit. ...
Page 3
... Programming Lockout Override” section). ERASURE: Before a byte/word can be reprogrammed, it must be erased. The erased state of memory bits is a logi- cal “1”. The entire device can be erased by using the Chip Erase command or individual sectors can be erased by using the Sector Erase commands ...
Page 4
... The command sequence for a chip erase suspend and a sector erase suspend are the same. PRODUCT IDENTIFICATION: The product identification mode identifies the device and manufacturer as Atmel. It may be accessed by hardware or software operation. The hardware operation mode can be used by an external pro- grammer to identify the correct programming algorithm for the Atmel product ...
Page 5
... During a program or erase operation, successive attempts to read data from the same memory plane will result in I/O6 toggling between “1” and “0”. Once the program cycle has completed, I/O6 will stop toggling and valid data will be read. Examining the toggle bit may begin at any time during a program cycle ...
Page 6
Command Definition in (Hex) 1st Bus Command Bus Sequence Cycles Addr Read 1 Addr Chip Erase 6 5555 Sector Erase 6 5555 Byte/Word Program 4 5555 Bypass Unlock 6 5555 Single-pulse 1 Addr Byte/Word Program Sector Lockout 6 5555 Erase ...
Page 7
AT49BV/LV8011 – Sector Address Table Plane Sector Size (Bytes/Words) A SA0 16K/8K A SA1 32K/16K A SA2 8K/4K A SA3 8K/4K A SA4 8K/4K A SA5 8K/4K A SA6 32K/16K A SA7 16K/8K B SA8 64K/32K B SA9 64K/32K B ...
Page 8
AT49BV/LV8011T – Sector Address Table Plane Sector Size (Bytes/Words) B SA0 64K/32K B SA1 64K/32K B SA2 64K/32K B SA3 64K/32K B SA4 64K/32K B SA5 64K/32K B SA6 64K/32K B SA7 64K/32K B SA8 64K/32K B SA9 64K/32K B ...
Page 9
... Software Notes can Refer to AC programming waveforms. = 12.0V ± 0.5V Manufacturer Code: 1FH (x8); 001FH (x16), Device Code: 00CB-AT49BV8011; 004A-AT49BV8011T. 5. See details under “Software Product Identification Entry/Exit”. 6. For faster program/erase operations Characteristics Symbol Parameter I Input Load Current LI I Output Leakage Current ...
Page 10
... OE tACC tRO RESET HIGH Z OUTPUT OUTPUT VALID - t after the address transition without impact on t ACC after the falling edge of CE without impact Output Test Load Max 6 12 AT49LV8011(T)-90 AT49BV8011(T)-12 Min Max Min Max 800 tDF tOH . ACC after an address change ...
Page 11
AC Byte/Word Load Characteristics Symbol Parameter Address, OE Setup Time AS OES t Address Hold Time AH t Chip Select Setup Time CS t Chip Select Hold Time CH t Write Pulse Width (WE or CE) WP ...
Page 12
Program Cycle Characteristics Symbol Parameter t Byte/Word Programming Time BP t Address Setup Time AS t Address Hold Time AH t Data Setup Time DS t Data Hold Time DH t Write Pulse Width WP t Write Pulse Width High ...
Page 13
Data Polling Characteristics Symbol Parameter t Data Hold Time Hold Time OEH ( Output Delay OE t Write Recovery Time WR Notes: 1. These parameters are characterized and not 100% tested. 2. See t ...
Page 14
... Device Code is read for The device does not remain in identification mode if pow- ered down. 4. The device returns to standard operation mode. 5. Manufacturer Code: 1FH(x8); 001FH(x16) 6. Device Code: 00CB-AT49BV8011; 004A-AT49BV8011T. 7. Either one of the Product ID Exit commands can be used. AT49BV/LV8011(T) 14 (1) Sector Lockout Enable Algorithm ...
Page 15
Status Bit Table Read Address In Plane A While Programming in Plane A Programming in Plane B Erasing in Plane A Erasing in Plane B Erase Suspended & Read Erasing Sector Erase Suspended & Read Non-erasing Sector Erase Suspended & ...
Page 16
... AT49BV8011-12CI 48C3 AT49BV8011-12TI 48T AT49LV8011T-90CC 48C3 AT49LV8011T-90TC 48T AT49LV8011T-90CI 48C3 AT49LV8011T-90TI 48T AT49BV8011T-12CC 48C3 AT49BV8011T-12TC 48T AT49BV8011T-12CI 48C3 AT49BV8011T-12TI 48T Package Type Operation Range Commercial (0° to 70°C) Industrial (-40° to 85°C) Commercial (0° to 70°C) Industrial (-40° to 85°C) Commercial (0° ...
Page 17
Packaging Information 48C3, 48-ball, Plastic Chip-size Ball Grid Array Package (CBGA) Dimensions in Millimeters and (Inches)* 7.15 (0.281) 6.85 (0.270) 7.15 (0.281) 6.85 (0.270) 4.0 (0.157 ...
Page 18
... No licenses to patents or other intellectual prop- erty of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life suppor t devices or systems. ...